SIB FPGA : C. 0. E Main Reset cause : Power-On SW-Boot : 0 U-Boot 2013.04 (Nov 29 2017 - 11:08:34) CPU0: P4080E, Version: 3.0, (0x82080030) Core: E500MC, Version: 3.1, (0x80230031) Clock Configuration: CPU0:1500 MHz, CPU1:1500 MHz, CPU2:1500 MHz, CPU3:1500 MHz, CPU4:1500 MHz, CPU5:1500 MHz, CPU6:1500 MHz, CPU7:1500 MHz, CCB:800 MHz, DDR:650 MHz (1300 MT/s data rate) (Asynchronous), LBC:50 MHz FMAN1: 450 MHz FMAN2: 450 MHz QMAN: 0 MHz PME: 450 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled checkboard(), line 442, file: eCCM2.c Board: P4080, 36-bit Addressing Reset Configuration Word (RCW): 00000000: 105a0000 00000000 1e1e521e 0000cccc 00000010: 40261100 fc3c2000 de800000 e1200000 00000020: 00000000 00000000 00000000 c09d8000 00000030: 00000000 00000000 00000000 00000000 CONFIG_BPTR_VIRT_ADDR = 0xfffff000 REF OUT programmed. U57 value read = 0X540109E8 U57 poked. U57 value read = 0X540109E4 CFL version register: 0x000A0000 CFL PCB VER register: 0x01040000 (HW Vintage: Rate 5 P4 eCCM2) SIB version register: 0x000C000E SIB PCB VER register: 0x00010004 SIB reset control : 0x10220003 SIB reset status register: 0x00000071 (reset reason= Power-On) WD count: 0 - ---------------------------------------------------------- - Max number of not validated board start attempts : 4 - Current number of not validated board start attempts : 0 - ---------------------------------------------------------- I2C: ready DRAM: Initializing....using fixed parameters Configuring DDR for 1300 MT/s data rate ddr_freq= 1300000000, ddr_freq_mhz= 1300 SIB 0x20: 0X71 $$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$ $$$ PMEM is OFF $$$ $$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$ fixed_sdram() returned 0x100000000 2 GiB left unmapped 4 GiB (DDR3, 64-bit, CL=9, ECC off) DDR Controller Interleaving Mode: cache line Testing 0x00000000 - 0x7fffffff memory_post_test_regions(start= 0x0, size= 0x40000000) -- testing at most 1GByte Testing 0x80000000 - 0xffffffff (advance) memory_post_test_regions(start= 0x0, size= 0x40000000) -- testing at most 1GByte Remap DDR 2 GiB left unmapped Now running in RAM - U-Boot at: 7fee0000 board_early_init_r(), line 573, file: eCCM2.c == console log starts ================== boot_id= 0, next_boot_id= 0 ====================================================== U12: SyncE Synth Status : 0xC0010511 LOCKED. U57: Eth Synth Status : 0xC0010511 LOCKED. SERDES Lo-speed Synth Status: 0xC0010511 LOCKED. SERDES Hi-speed Synth Status: 0xC0010511 LOCKED. Using eCCM2-rate5 ADF4116 R-data. Using eCCM2-rate5 ADF4116 N-data. REF OUT programmed. Using eCCM2-rate5 ADF4116 PLL init. Reference Output PLL status: 0xC0010511 LOCKED. ====================================================== POST memory PASSED Flash: 8 MiB L2: 128 KB enabled Corenet Platform Cache: 2048 KB enabled SERDES: bank 2 disabled SERDES: bank 3 disabled Work-around for Erratum SERDES A002690 enabled SERDES: bank 1 reset Using default environment Taking BCM56334 Eth Switch and Winpath3 out of Reset!!! PCIe1: Root Complex of Eth Sw, with errors. Clearing. Now 0x00000000fsl_pci_init(), line 329, file: fsl_pci_init.c, pci_num = 1 Outbound memory range: d00000000:d00040000 PCICSRBAR @ 0xff000000 fsl_pci_init(), line 398, file: fsl_pci_init.c, pci_num = 1 limiting size to ff000000 R0 bus_start: 0 phys_start: 0 size: ff000000 R64 bus_start: 1000000000 phys_start: 0 size: 100000000 fsl_pci_init(), line 422, file: fsl_pci_init.c, pci_num = 1 PCI reg:0 0000000d00040000:0000000d00000000 0000000000040000 00000000 PCI reg:1 0000000000000000:0000000000000000 0000000000000000 00000001 PCI reg:2 0000000ffe000000:00000000ff000000 0000000001000000 00000100 PCI reg:3 0000000000000000:0000000000000000 00000000ff000000 00000108 PCI reg:4 0000000000000000:0000001000000000 0000000100000000 00000108 fsl_pci_init(), line 454, file: fsl_pci_init.c, enabled= 1 fsl_pci_init(), line 513, file: fsl_pci_init.c, enabled= 1 x1, regs @ 0xfe200000 fsl_pci_init(), line 539, file: fsl_pci_init.c, pci_num = 1 fsl_pci_init(), line 555, file: fsl_pci_init.c, pci_num= 1 fsl_pci_init(), line 559, file: fsl_pci_init.c Scanning PCI bus 01 01:00.0 - 14e4:b334 - Network controller PCIe1: Bus 00 - 01 PCIe3: Root Complex of WP3, fsl_pci_init(), line 329, file: fsl_pci_init.c, pci_num = 3 Outbound memory range: c00000000:c80000000 PCICSRBAR @ 0xff000000 fsl_pci_init(), line 398, file: fsl_pci_init.c, pci_num = 3 limiting size to ff000000 R0 bus_start: 0 phys_start: 0 size: ff000000 R64 bus_start: 1000000000 phys_start: 0 size: 100000000 fsl_pci_init(), line 422, file: fsl_pci_init.c, pci_num = 3 PCI reg:0 0000000c80000000:0000000c00000000 0000000080000000 00000000 PCI reg:1 0000000000000000:0000000000000000 0000000000000000 00000001 PCI reg:2 0000000ffe000000:00000000ff000000 0000000001000000 00000100 PCI reg:3 0000000000000000:0000000000000000 00000000ff000000 00000108 PCI reg:4 0000000000000000:0000001000000000 0000000100000000 00000108 fsl_pci_init(), line 454, file: fsl_pci_init.c, enabled= 0 ....PCIe link not ready. LTSSM=0x00. Asserting PCIe reset @fe202f00 = 88400000 PCIe LTSSM=0x16 after reporting PCIe link not ready, extra msec=417 fsl_pci_init(), line 513, file: fsl_pci_init.c, enabled= 1 x1, regs @ 0xfe202000 fsl_pci_init(), line 539, file: fsl_pci_init.c, pci_num = 3 fsl_pci_init(), line 555, file: fsl_pci_init.c, pci_num= 3 fsl_pci_init(), line 581, file: fsl_pci_init.c pci_num = 3, line= 582 fsl_pci_init() - SAVING DATA TO my3_hose & my3_pci_info, line 585, file: fsl_pci_init.c PCIe3: Bus 02 - 03 In: serial Out: serial Err: serial Serdes Bank 1 RefClk = 125MHz PLL Locked Serdes Bank 2 RefClk = 100MHz PLL Unlocked Serdes Bank 3 RefClk = 125MHz PLL Unlocked =============================================================== high_ticks= 0x00000000, low_ticks= 0x02053386, random_ticks= 0x67466994 SIB scratch test PASSED! CPLD scratch test PASSED! SC scratch test PASSED! =============================================================== interrupt_init_cpu(); PMEM setup: eivpr11@fe050160 = 4F0000, eilr11@fe050178 = F0 =============================================================== EEPROM ENVIRONMENT : - Valid environment found in eeprom - Default environment variables list found - "eepromvarlist = ethaddr eth1addr eth2addr eth3addr eth4addr eth5addr ipaddr gatewayip serverip netmask" - Getting "ethaddr" variable value in eeprom : "00:11:3F:F8:5B:8A" - Setting variable value in default environment - Getting "eth1addr" variable value in eeprom : "00:11:3F:F8:5B:8B" - Setting variable value in default environment - Getting "eth2addr" variable value in eeprom : "00:11:3F:F8:5B:8C" - Setting variable value in default environment - Getting "eth3addr" variable value in eeprom : "00:11:3F:F8:5B:8D" - Setting variable value in default environment - Getting "eth4addr" variable value in eeprom : "00:11:3F:F8:5B:8E" - Setting variable value in default environment - Getting "eth5addr" variable value in eeprom : "00:11:3F:F8:5B:8F" - Setting variable value in default environment - Getting "ipaddr" variable value in eeprom : "192.168.10.1" - Setting variable value in default environment - Getting "gatewayip" variable value in eeprom : "000.000.000.000" - Setting variable value in default environment - Getting "serverip" variable value in eeprom : "000.000.000.000" !!! WARNING : variable serverip set to 0.0.0.0. Will use default value instead !!! - Getting "netmask" variable value in eeprom : "255.255.255.000" - Setting variable value in default environment =============================================================== Getting environment variable : bootid=0 Board Type is : 0x00000001 Getting environment variable : partition=nor0,0 Getting environment variable : bootpart=5 Getting environment variable : loadtype=LTE Getting environment variable : hardtype=U Net: Fman1: Uploading microcode version 101.8.0 Fman2: Uploading microcode version 101.8.0 FM2@DTSEC1, FM2@DTSEC2, FM2@DTSEC3 [PRIME], FM2@DTSEC4 !!! Please use ESC key to exit Autoboot Mode and type 'stop' in uboot prompt!!! TLBCAM entries entry 00: V: 1 TS: 0 EPN 0xffffc000-0xffffffff RPN 0x0ffffc000 *I*G* size= 0x 4000 size:16 KiB entry 01: V: 1 TS: 0 EPN 0xfe000000-0xfeffffff RPN 0xffe000000 *I*G* size= 0x 1000000 size:16 MiB entry 02: V: 1 TS: 0 EPN 0xefc00000-0xefffffff RPN 0xfefc00000 *I*G* size= 0x 400000 size:4 MiB entry 03: V: 1 TS: 0 EPN 0x00000000-0x3fffffff RPN 0x000000000 **M** size= 0x 40000000 size:1 GiB entry 04: V: 1 TS: 0 EPN 0xd0000000-0xdfffffff RPN 0xfd0000000 *I*G* size= 0x 10000000 size:256 MiB entry 05: V: 1 TS: 0 EPN 0xd1000000-0xd1ffffff RPN 0xfd1000000 *I*G* size= 0x 1000000 size:16 MiB entry 06: V: 1 TS: 0 EPN 0xd2000000-0xd200ffff RPN 0xfd2000000 *I*G* size= 0x 10000 size:64 KiB entry 07: V: 1 TS: 0 EPN 0xd5000000-0xd500ffff RPN 0xfd5000000 *I*G* size= 0x 10000 size:64 KiB entry 08: V: 1 TS: 0 EPN 0xef800000-0xefbfffff RPN 0xfef800000 *I*G* size= 0x 400000 size:4 MiB entry 09: V: 1 TS: 0 EPN 0xf4000000-0xf40fffff RPN 0xff4000000 ***** size= 0x 100000 size:1 MiB entry 10: V: 1 TS: 0 EPN 0xf4100000-0xf41fffff RPN 0xff4100000 *I*G* size= 0x 100000 size:1 MiB entry 11: V: 1 TS: 0 EPN 0xf4200000-0xf42fffff RPN 0xff4200000 ***** size= 0x 100000 size:1 MiB entry 12: V: 1 TS: 0 EPN 0xf4300000-0xf43fffff RPN 0xff4300000 *I*G* size= 0x 100000 size:1 MiB entry 13: V: 1 TS: 0 EPN 0xf0000000-0xf03fffff RPN 0xf00000000 *I*G* size= 0x 400000 size:4 MiB entry 14: V: 1 TS: 0 EPN 0x40000000-0x7fffffff RPN 0x040000000 **M** size= 0x 40000000 size:1 GiB entry 15: V: 1 TS: 0 EPN 0xffc00000-0xffcfffff RPN 0x0ffc00000 ***** size= 0x 100000 size:1 MiB entry 21: V: 1 TS: 0 EPN 0xe5000000-0xe503ffff RPN 0xd00040000 *I*G* size= 0x 40000 size:256 KiB entry 22: V: 1 TS: 0 EPN 0x80000000-0x803fffff RPN 0xc80000000 *I*G* size= 0x 400000 size:4 MiB entry 23: V: 1 TS: 0 EPN 0x80400000-0x8043ffff RPN 0xc80400000 *I*G* size= 0x 40000 size:256 KiB entry 24: V: 1 TS: 0 EPN 0x90000000-0x9fffffff RPN 0xca0000000 *I*G* size= 0x 10000000 size:256 MiB entry 25: V: 1 TS: 0 EPN 0xa0000000-0xafffffff RPN 0xcc0000000 *I*G* size= 0x 10000000 size:256 MiB entry 26: V: 1 TS: 0 EPN 0xb0000000-0xbfffffff RPN 0xce0000000 *I*G* size= 0x 10000000 size:256 MiB Local Access Window Configuration LAWBARH00: 0x0000000f LAWBARL00: 0xef800000 LAWAR00: 0x81f00016 (EN: 1 TGT: 0x1f SIZE: 8 MiB) LAWBARH01: 0x0000000f LAWBARL01: 0xf4000000 LAWAR01: 0x81800014 (EN: 1 TGT: 0x18 SIZE: 2 MiB) LAWBARH02: 0x0000000f LAWBARL02: 0xf4200000 LAWAR02: 0x83c00014 (EN: 1 TGT: 0x3c SIZE: 2 MiB) LAWBARH03: 0x0000000f LAWBARL03: 0xd0000000 LAWAR03: 0x81f00017 (EN: 1 TGT: 0x1f SIZE: 16 MiB) LAWBARH04: 0x0000000f LAWBARL04: 0xd5000000 LAWAR04: 0x81f0000e (EN: 1 TGT: 0x1f SIZE: 32 KiB) LAWBARH05: 0x0000000f LAWBARL05: 0xd1000000 LAWAR05: 0x81f00017 (EN: 1 TGT: 0x1f SIZE: 16 MiB) LAWBARH06: 0x0000000f LAWBARL06: 0xd2000000 LAWAR06: 0x81f0000e (EN: 1 TGT: 0x1f SIZE: 32 KiB) LAWBARH07: 0x0000000f LAWBARL07: 0x00000000 LAWAR07: 0x81d00015 (EN: 1 TGT: 0x1d SIZE: 4 MiB) LAWBARH08: 0x0000000d LAWBARL08: 0x00040000 LAWAR08: 0x80000011 (EN: 1 TGT: 0x00 SIZE: 256 KiB) LAWBARH09: 0x0000000c LAWBARL09: 0x80000000 LAWAR09: 0x8020001e (EN: 1 TGT: 0x02 SIZE: 2 GiB) LAWBARH31: 0x00000000 LAWBARL31: 0x00000000 LAWAR31: 0x8140001f (EN: 1 TGT: 0x14 SIZE: 4 GiB) Local Bus Controller Registers BR0 0xEF801001 OR0 0xFF8000F3 BR1 0x00000000 OR1 0x00000000 BR2 0xD0001001 OR2 0xFF0000F3 BR3 0xD1001001 OR3 0xFF0000F3 BR4 0xD2001001 OR4 0xFFFF80F3 BR5 0x00000000 OR5 0x00000000 BR6 0x00000000 OR6 0x00000000 BR7 0xD5001001 OR7 0xFFFF80A3 LBCR 0x40000000 LCRR 0x80020004 (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 2 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found 348399 bytes read in 305 ms (1.1 MiB/s) Uncompressed size: 1048576 = 0x100000 my_pci3scan(), line 620, file: fsl_pci_init.c, pci_num = 3 my_pci3scan(), line 630, file: fsl_pci_init.c my_pci3scan(), line 634, file: fsl_pci_init.c my_pci3scan(), line 636, file: fsl_pci_init.c Scanning PCI bus 03 03:00.0 - 1980:0003 - Network controller my_pci3scan(), line 646, file: fsl_pci_init.c my_pci3scan(), line 652, file: fsl_pci_init.c my_pci3scan(), line 659, file: fsl_pci_init.c my_pci3scan(), line 665, file: fsl_pci_init.c my_pci3scan(), line 671, file: fsl_pci_init.c my_pci3scan(), line 677, file: fsl_pci_init.c WP3: bar 0 LO = 0x00000004 HI = 0x0000000c, bus = 0x0000000c00000000 WP3: phys_addr = 0x0000000c80000000, virt_addr = 0x80000000 WP3: bar 2 LO = 0x2000000c HI = 0x0000000c, bus = 0x0000000c20000000 WP3: phys_addr = 0x0000000ca0000000, virt_addr = 0x90000000 WP3: bar 4 LO = 0x4000000c HI = 0x0000000c, bus = 0x0000000c40000000 WP3: phys_addr = 0x0000000cc0000000, virt_addr = 0xa0000000 my_pci3scan(), line 679, file: fsl_pci_init.c 3758925 bytes read in 474 ms (7.6 MiB/s) ***** Loading EFPGA from USB Flash ***** Uncompressed size: 9982936 = 0x9853D8 %%%%%%%%%%%%%%%%%%%%%%%% load_efpga() SUCCESS !!!, # of bytes= 9981344 EFPGA version register: 0x00300115 EFPGA scratch test PASSED! ** File not found firmware/ ** ** ZUC not loaded. ** do_sib_reflash(); addr= 02800000, size= 1048576, line 274, file: cmd_eCCM2.c sib_file_version = 0xc000e sib_version = 0xc000e sib_reset_status = 0x71 No SIB update needed! reset_status: 0x71 1875371 bytes read in 312 ms (5.7 MiB/s) *** Loading BIST *** Uncompressed size: 6282756 = 0x5FDE04 ## Starting application at 0x00040000 ... ********************************************* eCCM-2 is alive : r5V7.6; 11:14 11/29/2017 ********************************************* Bist Pointer : 0xffffd000 System Type : LTE Software Release : 7.6 Size : 4096 P4 Board... "BSTART� 22 06 42 53 54 41 52 54 88 00 00 00 22 09 50 43 43 *********************************************** **** START OF BIST HARDWARE INITIALIZATION **** *********************************************** bist_ad9522_spi_init: SPI initialised, AD9522 1 set in LSB first bist_ad9522_spi_init: SPI initialised, AD9522 1 set in LSB first ****************************************************** Configuration check for low speed serdes AD9522: Synth currently using version 0x302c, which is version for Vectron vendor, board versions newer than P0 - 10 MHz. No reprogramming needed. ****************************************************** ERROR : OM 10 MHz is not ready = 2b010250 !!!!!!!!!!!!!!!!!!!!!!!! Low speed lock detected; status=0xc0010511 bist_ad9522_spi_init: SPI initialised, AD9522 0 set in LSB first bist_ad9522_spi_init: SPI initialised, AD9522 0 set in LSB first ****************************************************** Configuration check for high speed serdes AD9522: Synth currently using version 0x302c, which is version for Vectron vendor, board versions newer than P0 - 10 MHz. No reprogramming needed. ****************************************************** ERROR : OM 10 MHz is not ready = 2b010250 !!!!!!!!!!!!!!!!!!!!!!!! High speed lock detected; status=0xc0010511 AD9522 for high speed SERDES: PLL init passed. bist_ad9522_spi_init: SPI initialised, AD9522 1 set in LSB first bist_ad9522_spi_init: SPI initialised, AD9522 1 set in LSB first ****************************************************** Configuration check for low speed serdes AD9522: Synth currently using version 0x302c, which is version for Vectron vendor, board versions newer than P0 - 10 MHz. No reprogramming needed. ==> Hit spacebar key 3x to stop autotest <== fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 fm_eth_open(), line 441, file: eth.c, speed= 1000, link= 1 ======================= BIST AUTO RESULT ========================= SIB_DWNL > PASS SIB_FROM_SPI_MAIN > PASS PCB_COMPLIANT > PASS FPGA Register acces> PASS WP3 PCI Access > PASS WP3 Internal RAM > PASS WP3 Packet RAM > PASS WP3 Parameter RAM > PASS AD9522_CALIB_HS > PASS AD9522_CALIB_LS > PASS AD9522_LOCK_HS > PASS AD9522_LOCK_LS > PASS PLL_10_15MHZ_LOCK > PASS AD9522 SPI INIT HS > PASS AD9522 SPI INIT LS > PASS AD9522 CFG CHK HS > PASS AD9522 CFG CHK LS > PASS CDCE CFG CHECK ETH > PASS CDCE CFG CHK SYNCE > PASS PCI1 INIT ETH SW > PASS eTSEC2 INT > PASS eTSEC1 SW INT > PASS eTSEC4 SW INT > PASS Int GPS Access > PASS eTSEC1_LAN > PASS JUMPER_UBOOT0 > PASS ETH_EFPGA_SGMII0 > PASS ETH_EFPGA_SGMII1 > PASS WP3_APPLI_SDRAM > PASS WP3_GE_SWITCH_INT > PASS WP3_GE_SWITCH_EXT > PASS WP3_BH_INTERNAL > PASS WP3_BH_PHY_INT > PASS WP3_BH_SFP_INT > PASS I2C CPU ACCESS > PASS I2C 10M MODULE > PASS I2C THERMAL SENSOR > PASS EFPGA_CPRI1_BER > PASS EFPGA_CPRI2_BER > PASS EFPGA_CPRI3_BER > PASS EFPGA_CPRI4_BER > PASS EFPGA_CPRI5_BER > PASS EFPGA_CPRI6_BER > PASS EFPGA_CPRI7_BER > PASS EFPGA_CPRI8_BER > PASS EFPGA_CPRI9_BER > PASS EFPGA_HSIQ01_BER > PASS EFPGA_HSIQ02_BER > PASS EFPGA_HSIQ03_BER > PASS EFPGA_HSIQ04_BER > PASS EFPGA_HSIQ05_BER > PASS EFPGA_HSIQ06_BER > PASS EFPGA_HSIQ07_BER > PASS EFPGA_HSIQ08_BER > PASS EFPGA_HSIQ09_BER > PASS EFPGA_HSIQ10_BER > PASS EFPGA_HSIQ11_BER > PASS EFPGA_HSIQ12_BER > PASS RTC > PASS U35 Temp Sensor > PASS U36 Temp Sensor > PASS U37 Temp Sensor > PASS U38 Temp Sensor > PASS OCXO Temp Sensor > PASS EFPGA Temp Sensor > PASS adr_err=0x0, actual=0x0, exp=0x0 data_R4=0x0 Auto test elapsed time: Not Available Uboot results location=0xffffd000 Uboot results size=0x1000 ======= LEAVING BIST ========= ## Application terminated, rc = 0x0 do_set_hd_watchdog(127), line 578, file: ../common/cmd_spec.c hw_watchdog_set(127), line 587, file: eCCM.c Old hardware watchdog value was : 127 New hardware watchdog value is : 127 ***** Loading Linux kernel from USB ***** 13367920 bytes read in 1085 ms (11.7 MiB/s) WARNING: adjusting available memory to 30000000 ## Booting kernel from FIT Image at 03000000 ... Using 'conf@1' configuration Trying 'kernel@1' kernel subimage Description: Linux-2.6.34 Type: Kernel Image Compression: gzip compressed Data Start: 0x030000e4 Data Size: 13330410 Bytes = 12.7 MiB Architecture: PowerPC OS: Linux Load Address: 0x00000000 Entry Point: 0x00000000 Hash algo: crc32 Hash value: 0c5903a3 Hash algo: sha1 Hash value: 4bf2092a1b14335fe6aebecdc140b99da3c41f5a Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 03000000 Using 'conf@1' configuration Trying 'fdt@1' FDT blob subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x03cb69f8 Data Size: 36164 Bytes = 35.3 KiB Architecture: PowerPC Hash algo: crc32 Hash value: 7f47a272 Hash algo: sha1 Hash value: 8a2d55ad8a7babadc6bfe711f4eb7fef4326ff92 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x03cb69f8 CONFIG_SYS_BOOTM_LEN=0x4000000 Uncompressing Kernel Image ... OK Loading Device Tree to 03fe4000, end 03fffd43 ... OK ft_board_setup(), line 826, file: eCCM2.c Data at 00000007 is not an Fman firmware board_ft_fman_fixup_port(port= 10, offset= 33956, prop='fsl,fman-1g-mac'), line 232, file: eth_p4080.c board_ft_fman_fixup_port(port= 11, offset= 34424, prop='fsl,fman-1g-mac'), line 232, file: eth_p4080.c board_ft_fman_fixup_port(port= 12, offset= 34860, prop='fsl,fman-1g-mac'), line 232, file: eth_p4080.c board_ft_fman_fixup_port(port= 13, offset= 35312, prop='fsl,fman-1g-mac'), line 232, file: eth_p4080.c fdt_fixup_board_enet(), line 251, file: eth_p4080.c [ 0.000000] Using eCCM2 machine description [ 0.000000] vxTLB1:MAS0, x10000001 [ 0.000000] vxTLB1:MAS1, xc0000900 [ 0.000000] vxTLB1:MAS2, xc0000004 [ 0.000000] vxTLB1:MAS3, x00000015 [ 0.000000] vxTLB1:MAS7, x00000000 [ 0.000000] vxTLB1:MAS0, x10010002 [ 0.000000] vxTLB1:MAS1, xc0000900 [ 0.000000] vxTLB1:MAS2, xd0000004 [ 0.000000] vxTLB1:MAS3, x10000015 [ 0.000000] vxTLB1:MAS7, x00000000 [ 0.000000] vxTLB1:MAS0, x10020003 [ 0.000000] vxTLB1:MAS1, xc0000900 [ 0.000000] vxTLB1:MAS2, xe0000004 [ 0.000000] vxTLB1:MAS3, x20000015 [ 0.000000] vxTLB1:MAS7, x00000000 [ 0.000000] Memory CAM mapping: 256/256/256/0/0/0/0/0/0/0 Mb, residual: 3157Mb [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.34.15-grsec-eccm2 (issltelb@frmrssucc049) (gcc version 4.4.1 (Wind River Linux Sourcery G++ 4.4a-464) ) #2 SMP PREEMPT Wed Nov 29 11:11:51 CET 2017 [ 0.000000] Qman ver:0a01,01,02 [ 0.000000] No /soc@ffe000000/qman@318000 property 'fsl,qman-fqd', using lmb_alloc(0000000000200000) [ 0.000000] No /soc@ffe000000/qman@318000 property 'fsl,qman-pfdr', using lmb_alloc(0000000001000000) [ 0.000000] No /soc@ffe000000/bman@31a000 property 'fsl,bman-fbpr', using lmb_alloc(0000000001000000) [ 0.000000] Bman ver:0a02,01,00 [ 0.000000] CPU maps initialized for 1 thread per core [ 0.000000] bootconsole [udbg0] enabled setup_arch: bootmem [ 0.000000] Found FSL PCI host bridge at 0x0000000ffe202000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pcie@ffe202000 ranges: [ 0.000000] MEM 0x0000000c80000000..0x0000000c807fffff -> 0x0000000c00000000 [ 0.000000] MEM 0x0000000ca0000000..0x0000000cffffffff -> 0x0000000c20000000 Prefetch [ 0.000000] /pcie@ffe202000: PCICSRBAR @ 0xff000000 [ 0.000000] Found FSL PCI host bridge at 0x0000000ffe200000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pcie@ffe200000 ranges: [ 0.000000] MEM 0x0000000d00040000..0x0000000d0007ffff -> 0x0000000d00000000 [ 0.000000] IO 0x0000000d01000000..0x0000000d010fffff -> 0x00000000c1000000 [ 0.000000] /pcie@ffe200000: PCICSRBAR @ 0xff000000 [ 0.000000] eCCM2 board from Alcatel-Lucent arch: exit [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00030000 [ 0.000000] Normal empty [ 0.000000] HighMem 0x00030000 -> 0x000f5500 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x000f5500 [ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts [ 0.000000] PERCPU: Embedded 10 pages/cpu @c30c7000 s17820 r8192 d14948 u65536 [ 0.000000] pcpu-alloc: s17820 r8192 d14948 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 996950 [ 0.000000] Kernel command line: ip=192.168.10.1::000.000.000.000:255.255.255.000::eth2 :on console=ttyS0,115200 mem=3925M default_hugepagesz=4M hugepagesz=4M hugepages=0 bootid=0 bootdev=sda bootpart=5 load2 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 3933012k/4019200k available (17276k kernel code, 86188k reserved, 256k data, 887k bss, 10004k init) [ 0.000000] Kernel virtual memory layout: [ 0.000000] * 0xfff57000..0xfffff000 : fixmap [ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs [ 0.000000] * 0xffaf8000..0xffc00000 : early ioremap [ 0.000000] * 0xf1000000..0xffaf8000 : vmalloc & ioremap [ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Experimental preemptable hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is enabled. [ 0.000000] NR_IRQS:512 nr_irqs:512 [ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe040000, max 8 CPUs [ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff [ 0.000000] mpic: Initializing for 256 sources [ 0.000000] DBG in arch/powerpc/platforms/85xx/demux_it_boot.c:bootFpga_init_IRQ#284: bootfpga irq= 16 [ 0.000000] DBG in arch/powerpc/platforms/85xx/demux_it_sc.c:scFpga_init_IRQ#290: scfpga irq= 17 [ 0.000000] INFO: bblink_init_IRQ#729: init bblink irqs [ 0.000000] INFO: bblink_init_IRQ#786: bblinkfpga virq= 18,hwirq=3 [ 0.000000] CPLD hw version reg: 0x01040000, board type: BSP_ECCM2(3) [ 0.000000] clocksource: timebase mult[5000000] shift[22] registered [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] ram_console: no valid data in buffer (sig = 0xdeadbeef) [ 0.000000] Using eCCM2 machine description [ 0.000000] vxTLB1:MAS0, x10000001 [ 0.000000] vxTLB1:MAS1, xc0000900 [ 0.000000] vxTLB1:MAS2, xc0000004 [ 0.000000] vxTLB1:MAS3, x00000015 [ 0.000000] vxTLB1:MAS7, x00000000 [ 0.000000] vxTLB1:MAS0, x10010002 [ 0.000000] vxTLB1:MAS1, xc0000900 [ 0.000000] vxTLB1:MAS2, xd0000004 [ 0.000000] vxTLB1:MAS3, x10000015 [ 0.000000] vxTLB1:MAS7, x00000000 [ 0.000000] vxTLB1:MAS0, x10020003 [ 0.000000] vxTLB1:MAS1, xc0000900 [ 0.000000] vxTLB1:MAS2, xe0000004 [ 0.000000] vxTLB1:MAS3, x20000015 [ 0.000000] vxTLB1:MAS7, x00000000 [ 0.000000] Memory CAM mapping: 256/256/256/0/0/0/0/0/0/0 Mb, residual: 3157Mb [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.34.15-grsec-eccm2 (issltelb@frmrssucc049) (gcc version 4.4.1 (Wind River Linux Sourcery G++ 4.4a-464) ) #2 SMP PREEMPT Wed Nov 29 11:11:51 CET 2017 [ 0.000000] Qman ver:0a01,01,02 [ 0.000000] No /soc@ffe000000/qman@318000 property 'fsl,qman-fqd', using lmb_alloc(0000000000200000) [ 0.000000] No /soc@ffe000000/qman@318000 property 'fsl,qman-pfdr', using lmb_alloc(0000000001000000) [ 0.000000] No /soc@ffe000000/bman@31a000 property 'fsl,bman-fbpr', using lmb_alloc(0000000001000000) [ 0.000000] Bman ver:0a02,01,00 [ 0.000000] CPU maps initialized for 1 thread per core [ 0.000000] bootconsole [udbg0] enabled [ 0.000000] Found FSL PCI host bridge at 0x0000000ffe202000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pcie@ffe202000 ranges: [ 0.000000] MEM 0x0000000c80000000..0x0000000c807fffff -> 0x0000000c00000000 [ 0.000000] MEM 0x0000000ca0000000..0x0000000cffffffff -> 0x0000000c20000000 Prefetch [ 0.000000] /pcie@ffe202000: PCICSRBAR @ 0xff000000 [ 0.000000] Found FSL PCI host bridge at 0x0000000ffe200000. Firmware bus number: 0->1 [ 0.000000] PCI host bridge /pcie@ffe200000 ranges: [ 0.000000] MEM 0x0000000d00040000..0x0000000d0007ffff -> 0x0000000d00000000 [ 0.000000] IO 0x0000000d01000000..0x0000000d010fffff -> 0x00000000c1000000 [ 0.000000] /pcie@ffe200000: PCICSRBAR @ 0xff000000 [ 0.000000] eCCM2 board from Alcatel-Lucent [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00030000 [ 0.000000] Normal empty [ 0.000000] HighMem 0x00030000 -> 0x000f5500 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x000f5500 [ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts [ 0.000000] PERCPU: Embedded 10 pages/cpu @c30c7000 s17820 r8192 d14948 u65536 [ 0.000000] pcpu-alloc: s17820 r8192 d14948 u65536 alloc=16*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 996950 [ 0.000000] Kernel command line: ip=192.168.10.1::000.000.000.000:255.255.255.000::eth2 :on console=ttyS0,115200 mem=3925M default_hugepagesz=4M hugepagesz=4M hugepages=0 bootid=0 bootdev=sda bootpart=5 load2 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 3933012k/4019200k available (17276k kernel code, 86188k reserved, 256k data, 887k bss, 10004k init) [ 0.000000] Kernel virtual memory layout: [ 0.000000] * 0xfff57000..0xfffff000 : fixmap [ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs [ 0.000000] * 0xffaf8000..0xffc00000 : early ioremap [ 0.000000] * 0xf1000000..0xffaf8000 : vmalloc & ioremap [ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Experimental preemptable hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is enabled. [ 0.000000] NR_IRQS:512 nr_irqs:512 [ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe040000, max 8 CPUs [ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff [ 0.000000] mpic: Initializing for 256 sources [ 0.000000] DBG in arch/powerpc/platforms/85xx/demux_it_boot.c:bootFpga_init_IRQ#284: bootfpga irq= 16 [ 0.000000] DBG in arch/powerpc/platforms/85xx/demux_it_sc.c:scFpga_init_IRQ#290: scfpga irq= 17 [ 0.000000] INFO: bblink_init_IRQ#729: init bblink irqs [ 0.000000] INFO: bblink_init_IRQ#786: bblinkfpga virq= 18,hwirq=3 [ 0.000000] CPLD hw version reg: 0x01040000, board type: BSP_ECCM2(3) [ 0.000000] clocksource: timebase mult[5000000] shift[22] registered [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] ram_console: no valid data in buffer (sig = 0xdeadbeef) [ 0.000000] console [ram-1] enabled [ 0.449260] Mount-cache hash table entries: 512 [ 0.457097] Initializing cgroup subsys net_cls [ 0.461481] Initializing scheduling traces [ 0.466351] SCHEDT#1746 : Schedt debug mode set by 0/0 [ 0.471521] mpic: requesting IPIs... [ 0.475026] alloc irq_desc for 251 on node 0 [ 0.479434] alloc kstat_irqs on node 0 [ 0.483367] irq: irq 251 on host /soc@ffe000000/pic@40000 mapped to virtual irq 251 [ 0.490988] alloc irq_desc for 252 on node 0 [ 0.495404] alloc kstat_irqs on node 0 [ 0.499314] irq: irq 252 on host /soc@ffe000000/pic@40000 mapped to virtual irq 252 [ 0.506954] alloc irq_desc for 253 on node 0 [ 0.511375] alloc kstat_irqs on node 0 [ 0.515285] irq: irq 253 on host /soc@ffe000000/pic@40000 mapped to virtual irq 253 [ 0.522923] alloc irq_desc for 254 on node 0 [ 0.527346] alloc kstat_irqs on node 0 [ 0.531256] irq: irq 254 on host /soc@ffe000000/pic@40000 mapped to virtual irq 254 [ 0.771384] Init trace_clock_cyc2ns: precalc_mult = 5120, precalc_shift = 8 [ 0.992516] Processor 1 found. [ 1.232613] Processor 2 found. [ 1.472723] Processor 3 found. [ 1.712818] Processor 4 found. [ 1.952911] Processor 5 found. [ 2.193003] Processor 6 found. [ 2.433094] Processor 7 found. [ 2.436095] Brought up 8 CPUs [ 2.439878] NET: Registered protocol family 16 [ 2.446072] e500 family performance monitor hardware support registered [ 2.452778] alloc irq_desc for 44 on node 0 [ 2.457039] alloc kstat_irqs on node 0 [ 2.460963] irq: irq 44 on host /soc@ffe000000/pic@40000 mapped to virtual irq 44 [ 2.468728] check_res_of_trace_clock: sched_clock() high resolution [ 2.475585] PCI: Probing PCI hardware [ 2.479215] PCI: I/O resource not set for host bridge /pcie@ffe202000 (domain 0) [ 2.486541] pci_bus NULL: scanning bus [ 2.490279] pci pci: found [1957:0400] class 000b20 header type 01 [ 2.496429] pci pci: ignoring class b20 (doesn't match header type 01) [ 2.502948] pci pci: calling fixup_hide_host_resource_fsl+0x0/0x70 [ 2.509106] pci pci: calling pcibios_fixup_resources+0x0/0x14c [ 2.514924] pci pci: calling quirk_fsl_pcie_header+0x0/0x70 [ 2.520477] pci pci: calling quirk_resource_alignment+0x0/0x39c [ 2.526386] pci pci: supports D1 D2 [ 2.529845] pci pci: PME# supported from D0 D1 D2 D3hot D3cold [ 2.535662] pci pci: PME# disabled [ 2.539069] pci_bus NULL: fixups for bus [ 2.542971] alloc irq_desc for 19 on node 0 [ 2.547290] alloc kstat_irqs on node 0 [ 2.551202] irq: irq 16 on host /soc@ffe000000/pic@40000 mapped to virtual irq 19 [ 2.558664] pci pci: scanning [bus 01-01] behind bridge, pass 0 [ 2.564571] pci pci: scanning [bus 00-00] behind bridge, pass 1 [ 2.570481] pci_bus NULL: scanning bus [ 2.574214] pci pci: found [1980:0003] class 000280 header type 00 [ 2.580384] pci pci: reg 10: [mem 0xc00000000-0xc007fffff 64bit] [ 2.586361] pci pci: reg 18: [mem 0xc20000000-0xc3fffffff 64bit pref] [ 2.592788] pci pci: reg 20: [mem 0xc40000000-0xc7fffffff 64bit pref] [ 2.599208] pci pci: calling pcibios_fixup_resources+0x0/0x14c [ 2.605020] pci pci: calling quirk_resource_alignment+0x0/0x39c [ 2.610939] pci pci: PME# supported from D0 D3hot D3cold [ 2.616216] pci pci: PME# disabled [ 2.619607] pci_bus NULL: fixups for bus [ 2.623502] pci pci: PCI bridge to [bus 01-ff] [ 2.627935] pci pci: bridge window [io 0x1000-0x0000] (disabled) [ 2.634180] pci pci: bridge window [mem 0x00000000-0x7fffffff] (disabled) [ 2.641128] pci pci: bridge window [mem 0x10000000-0x000fffff pref] (disabled) [ 2.648520] alloc irq_desc for 42 on node 0 [ 2.652839] alloc kstat_irqs on node 0 [ 2.656751] irq: irq 42 on host /soc@ffe000000/pic@40000 mapped to virtual irq 42 [ 2.664211] pci_bus NULL: bus scan returning with max=01 [ 2.669511] pci_bus NULL: bus scan returning with max=01 [ 2.675056] pci_bus NULL: scanning bus [ 2.678721] pci pci: found [1957:0400] class 000b20 header type 01 [ 2.684885] pci pci: ignoring class b20 (doesn't match header type 01) [ 2.691388] pci pci: calling fixup_hide_host_resource_fsl+0x0/0x70 [ 2.697554] pci pci: calling pcibios_fixup_resources+0x0/0x14c [ 2.703366] pci pci: calling quirk_fsl_pcie_header+0x0/0x70 [ 2.708927] pci pci: calling quirk_resource_alignment+0x0/0x39c [ 2.714828] pci pci: supports D1 D2 [ 2.718292] pci pci: PME# supported from D0 D1 D2 D3hot D3cold [ 2.724113] pci pci: PME# disabled [ 2.727513] pci_bus NULL: fixups for bus [ 2.731412] pci pci: scanning [bus 01-01] behind bridge, pass 0 [ 2.737305] pci pci: bus configuration invalid, reconfiguring [ 2.743033] pci pci: scanning [bus 00-00] behind bridge, pass 1 [ 2.748950] pci_bus NULL: scanning bus [ 2.752685] pci pci: found [14e4:b334] class 000200 header type 00 [ 2.758840] pci pci: reg 10: [mem 0xd00000000-0xd0003ffff 64bit] [ 2.764846] pci pci: calling pcibios_fixup_resources+0x0/0x14c [ 2.770635] pci pci: calling quirk_resource_alignment+0x0/0x39c [ 2.776573] pci pci: PME# supported from D0 D3hot D3cold [ 2.781832] pci pci: PME# disabled [ 2.785226] pci_bus NULL: fixups for bus [ 2.789125] pci pci: PCI bridge to [bus 03-ff] [ 2.793550] pci pci: bridge window [io 0x1000-0x0000] (disabled) [ 2.799802] pci pci: bridge window [mem 0x00000000-0x000fffff] (disabled) [ 2.806744] pci pci: bridge window [mem 0x10000000-0x000fffff pref] (disabled) [ 2.814142] alloc irq_desc for 40 on node 0 [ 2.818458] alloc kstat_irqs on node 0 [ 2.822366] irq: irq 40 on host /soc@ffe000000/pic@40000 mapped to virtual irq 40 [ 2.829834] pci_bus NULL: bus scan returning with max=03 [ 2.835127] pci_bus NULL: bus scan returning with max=03 [ 2.840632] PCI: Cannot allocate resource region 0 of PCI bridge 2, will remap [ 2.847760] PCI: Cannot allocate resource region 0 of PCI bridge 3, will remap [ 2.854998] PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff] [ 2.861310] pci pci: PCI bridge to [bus 01-01] [ 2.865735] pci pci: bridge window [io 0x0000-0xffffffff] [ 2.871372] pci pci: bridge window [mem 0xc80000000-0xc807fffff] [ 2.877538] pci pci: bridge window [mem 0xca0000000-0xcffffffff 64bit pref] [ 2.884659] pci pci: BAR 7: can't assign io (size 0x100000) [ 2.890211] pci pci: PCI bridge to [bus 03-03] [ 2.894632] pci pci: bridge window [io disabled] [ 2.899494] pci pci: bridge window [mem 0xd00040000-0xd0007ffff] [ 2.905660] pci pci: bridge window [mem pref disabled] [ 2.910956] pci_bus NULL: resource 0 [io 0x0000-0xffffffff] [ 2.916597] pci_bus NULL: resource 1 [mem 0xc80000000-0xc807fffff] [ 2.922756] pci_bus NULL: resource 2 [mem 0xca0000000-0xcffffffff pref] [ 2.929356] pci_bus NULL: resource 0 [io 0x0000-0xffffffff] [ 2.934995] pci_bus NULL: resource 1 [mem 0xc80000000-0xc807fffff] [ 2.941161] pci_bus NULL: resource 2 [mem 0xca0000000-0xcffffffff 64bit pref] [ 2.948276] pci_bus NULL: resource 1 [mem 0xd00040000-0xd0007ffff] [ 2.954442] pci_bus NULL: resource 1 [mem 0xd00040000-0xd0007ffff] [ 2.966067] bio: create slab at 0 [ 2.970368] vgaarb: loaded [ 2.973223] SCSI subsystem initialized [ 2.977189] usbcore: registered new interface driver usbfs [ 2.982679] usbcore: registered new interface driver hub [ 2.987992] usbcore: registered new device driver usb [ 2.993205] Bman err interrupt handler present [ 2.997656] alloc irq_desc for 105 on node 0 [ 3.002004] alloc kstat_irqs on node 0 [ 3.005924] irq: irq 105 on host /soc@ffe000000/pic@40000 mapped to virtual irq 105 [ 3.013581] alloc irq_desc for 107 on node 0 [ 3.017973] alloc kstat_irqs on node 0 [ 3.021888] irq: irq 107 on host /soc@ffe000000/pic@40000 mapped to virtual irq 107 [ 3.029553] alloc irq_desc for 109 on node 0 [ 3.033947] alloc kstat_irqs on node 0 [ 3.037859] irq: irq 109 on host /soc@ffe000000/pic@40000 mapped to virtual irq 109 [ 3.045518] alloc irq_desc for 111 on node 0 [ 3.049918] alloc kstat_irqs on node 0 [ 3.053829] irq: irq 111 on host /soc@ffe000000/pic@40000 mapped to virtual irq 111 [ 3.061489] alloc irq_desc for 113 on node 0 [ 3.065889] alloc kstat_irqs on node 0 [ 3.069800] irq: irq 113 on host /soc@ffe000000/pic@40000 mapped to virtual irq 113 [ 3.077460] alloc irq_desc for 115 on node 0 [ 3.081860] alloc kstat_irqs on node 0 [ 3.085771] irq: irq 115 on host /soc@ffe000000/pic@40000 mapped to virtual irq 115 [ 3.093432] alloc irq_desc for 117 on node 0 [ 3.097831] alloc kstat_irqs on node 0 [ 3.101742] irq: irq 117 on host /soc@ffe000000/pic@40000 mapped to virtual irq 117 [ 3.109403] alloc irq_desc for 119 on node 0 [ 3.113802] alloc kstat_irqs on node 0 [ 3.117714] irq: irq 119 on host /soc@ffe000000/pic@40000 mapped to virtual irq 119 [ 3.125373] alloc irq_desc for 121 on node 0 [ 3.129774] alloc kstat_irqs on node 0 [ 3.133685] irq: irq 121 on host /soc@ffe000000/pic@40000 mapped to virtual irq 121 [ 3.141347] alloc irq_desc for 123 on node 0 [ 3.145745] alloc kstat_irqs on node 0 [ 3.149656] irq: irq 123 on host /soc@ffe000000/pic@40000 mapped to virtual irq 123 [ 3.157512] Bman portal initialised, cpu 7 [ 3.161639] Bman portal initialised, cpu 6 [ 3.165746] Bman portal initialised, cpu 5 [ 3.169856] Bman portal initialised, cpu 4 [ 3.173982] Bman portal initialised, cpu 3 [ 3.178084] Bman portal initialised, cpu 2 [ 3.182181] Bman portal initialised, cpu 1 [ 3.186288] Bman portal initialised, cpu 0 [ 3.190466] Bman: reserved bpid 0, seeded 256 items [ 3.195320] Bman portals initialised [ 3.198940] Qman err interrupt handler present [ 3.204870] alloc irq_desc for 118 on node 0 [ 3.209219] alloc kstat_irqs on node 0 [ 3.213138] irq: irq 118 on host /soc@ffe000000/pic@40000 mapped to virtual irq 118 [ 3.222318] alloc irq_desc for 120 on node 0 [ 3.226667] alloc kstat_irqs on node 0 [ 3.230581] irq: irq 120 on host /soc@ffe000000/pic@40000 mapped to virtual irq 120 [ 3.239763] alloc irq_desc for 122 on node 0 [ 3.244111] alloc kstat_irqs on node 0 [ 3.248025] irq: irq 122 on host /soc@ffe000000/pic@40000 mapped to virtual irq 122 [ 3.257450] Qman portal initialised, cpu 0 [ 3.261508] note: qman_affine1[311] exited with preempt_count 1 [ 3.267366] Qman portal (slave) initialised, cpu 1 [ 3.272177] note: qman_affine2[312] exited with preempt_count 1 [ 3.278037] Qman portal (slave) initialised, cpu 2 [ 3.282855] note: qman_affine3[313] exited with preempt_count 1 [ 3.288713] Qman portal (slave) initialised, cpu 3 [ 3.293526] note: qman_affine4[314] exited with preempt_count 1 [ 3.299390] Qman portal (slave) initialised, cpu 4 [ 3.304203] note: qman_affine5[315] exited with preempt_count 1 [ 3.310066] Qman portal (slave) initialised, cpu 5 [ 3.314880] note: qman_affine6[316] exited with preempt_count 1 [ 3.320743] Qman portal (slave) initialised, cpu 6 [ 3.325556] note: qman_affine7[317] exited with preempt_count 1 [ 3.331419] Qman portal (slave) initialised, cpu 7 [ 3.336471] Qman portals initialised [ 3.340265] Switching to clocksource timebase [ 3.345562] NET: Registered protocol family 2 [ 3.349935] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 3.357403] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 3.364434] TCP bind hash table entries: 8192 (order: 4, 98304 bytes) [ 3.370851] TCP: Hash tables configured (established 8192 bind 8192) [ 3.377118] TCP reno registered [ 3.380243] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 3.386159] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 3.392620] NET: Registered protocol family 1 [ 3.397165] RPC: Registered udp transport module. [ 3.401785] RPC: Registered tcp transport module. [ 3.406461] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.412902] pci pci: calling quirk_cardbus_legacy+0x0/0x60 [ 3.418362] pci pci: calling quirk_usb_early_handoff+0x0/0xbdc [ 3.424181] pci pci: calling quirk_cardbus_legacy+0x0/0x60 [ 3.429646] pci pci: calling quirk_usb_early_handoff+0x0/0xbdc [ 3.435459] pci pci: calling quirk_cardbus_legacy+0x0/0x60 [ 3.440928] pci pci: calling quirk_usb_early_handoff+0x0/0xbdc [ 3.446743] pci pci: calling quirk_cardbus_legacy+0x0/0x60 [ 3.452212] pci pci: calling quirk_usb_early_handoff+0x0/0xbdc [ 3.458025] PCI: CLS 32 bytes, default 64 [ 3.741523] alloc irq_desc for 36 on node 0 [ 3.745790] alloc kstat_irqs on node 0 [ 3.749708] irq: irq 36 on host /soc@ffe000000/pic@40000 mapped to virtual irq 36 [ 3.757193] alloc irq_desc for 37 on node 0 [ 3.761497] alloc kstat_irqs on node 0 [ 3.765409] irq: irq 37 on host /soc@ffe000000/pic@40000 mapped to virtual irq 37 [ 3.777582] Setting up Freescale MSI support [ 3.781808] alloc irq_desc for 224 on node 0 [ 3.786184] alloc kstat_irqs on node 0 [ 3.790096] irq: irq 224 on host /soc@ffe000000/pic@40000 mapped to virtual irq 224 [ 3.797741] alloc irq_desc for 225 on node 0 [ 3.802155] alloc kstat_irqs on node 0 [ 3.806066] irq: irq 225 on host /soc@ffe000000/pic@40000 mapped to virtual irq 225 [ 3.813713] alloc irq_desc for 226 on node 0 [ 3.818126] alloc kstat_irqs on node 0 [ 3.822037] irq: irq 226 on host /soc@ffe000000/pic@40000 mapped to virtual irq 226 [ 3.829685] alloc irq_desc for 227 on node 0 [ 3.834097] alloc kstat_irqs on node 0 [ 3.838004] irq: irq 227 on host /soc@ffe000000/pic@40000 mapped to virtual irq 227 [ 3.845656] alloc irq_desc for 228 on node 0 [ 3.850068] alloc kstat_irqs on node 0 [ 3.853979] irq: irq 228 on host /soc@ffe000000/pic@40000 mapped to virtual irq 228 [ 3.861627] alloc irq_desc for 229 on node 0 [ 3.866040] alloc kstat_irqs on node 0 [ 3.869950] irq: irq 229 on host /soc@ffe000000/pic@40000 mapped to virtual irq 229 [ 3.877595] alloc irq_desc for 230 on node 0 [ 3.882011] alloc kstat_irqs on node 0 [ 3.885921] irq: irq 230 on host /soc@ffe000000/pic@40000 mapped to virtual irq 230 [ 3.893569] alloc irq_desc for 231 on node 0 [ 3.897982] alloc kstat_irqs on node 0 [ 3.901892] irq: irq 231 on host /soc@ffe000000/pic@40000 mapped to virtual irq 231 [ 3.909624] Setting up Freescale MSI support [ 3.913833] alloc irq_desc for 232 on node 0 [ 3.918225] alloc kstat_irqs on node 0 [ 3.922143] irq: irq 232 on host /soc@ffe000000/pic@40000 mapped to virtual irq 232 [ 3.929786] alloc irq_desc for 233 on node 0 [ 3.934197] alloc kstat_irqs on node 0 [ 3.938104] irq: irq 233 on host /soc@ffe000000/pic@40000 mapped to virtual irq 233 [ 3.945756] alloc irq_desc for 234 on node 0 [ 3.950167] alloc kstat_irqs on node 0 [ 3.954078] irq: irq 234 on host /soc@ffe000000/pic@40000 mapped to virtual irq 234 [ 3.961726] alloc irq_desc for 235 on node 0 [ 3.966139] alloc kstat_irqs on node 0 [ 3.970049] irq: irq 235 on host /soc@ffe000000/pic@40000 mapped to virtual irq 235 [ 3.977694] alloc irq_desc for 236 on node 0 [ 3.982110] alloc kstat_irqs on node 0 [ 3.986021] irq: irq 236 on host /soc@ffe000000/pic@40000 mapped to virtual irq 236 [ 3.993668] alloc irq_desc for 237 on node 0 [ 3.998087] alloc kstat_irqs on node 0 [ 4.001992] irq: irq 237 on host /soc@ffe000000/pic@40000 mapped to virtual irq 237 [ 4.009640] alloc irq_desc for 238 on node 0 [ 4.014052] alloc kstat_irqs on node 0 [ 4.017960] irq: irq 238 on host /soc@ffe000000/pic@40000 mapped to virtual irq 238 [ 4.025611] alloc irq_desc for 239 on node 0 [ 4.030024] alloc kstat_irqs on node 0 [ 4.033934] irq: irq 239 on host /soc@ffe000000/pic@40000 mapped to virtual irq 239 [ 4.041662] Setting up Freescale MSI support [ 4.045871] alloc irq_desc for 240 on node 0 [ 4.050264] alloc kstat_irqs on node 0 [ 4.054181] irq: irq 240 on host /soc@ffe000000/pic@40000 mapped to virtual irq 240 [ 4.061824] alloc irq_desc for 241 on node 0 [ 4.066235] alloc kstat_irqs on node 0 [ 4.070146] irq: irq 241 on host /soc@ffe000000/pic@40000 mapped to virtual irq 241 [ 4.077791] alloc irq_desc for 242 on node 0 [ 4.082206] alloc kstat_irqs on node 0 [ 4.086117] irq: irq 242 on host /soc@ffe000000/pic@40000 mapped to virtual irq 242 [ 4.093765] alloc irq_desc for 243 on node 0 [ 4.098178] alloc kstat_irqs on node 0 [ 4.102088] irq: irq 243 on host /soc@ffe000000/pic@40000 mapped to virtual irq 243 [ 4.109736] alloc irq_desc for 244 on node 0 [ 4.114149] alloc kstat_irqs on node 0 [ 4.118056] irq: irq 244 on host /soc@ffe000000/pic@40000 mapped to virtual irq 244 [ 4.125708] alloc irq_desc for 245 on node 0 [ 4.130120] alloc kstat_irqs on node 0 [ 4.134030] irq: irq 245 on host /soc@ffe000000/pic@40000 mapped to virtual irq 245 [ 4.141679] alloc irq_desc for 246 on node 0 [ 4.146091] alloc kstat_irqs on node 0 [ 4.150002] irq: irq 246 on host /soc@ffe000000/pic@40000 mapped to virtual irq 246 [ 4.157647] alloc irq_desc for 247 on node 0 [ 4.162062] alloc kstat_irqs on node 0 [ 4.165973] irq: irq 247 on host /soc@ffe000000/pic@40000 mapped to virtual irq 247 [ 4.177647] Freescale PowerQUICC MII Bus: probed [ 4.182383] mdio_bus NULL: /soc@ffe000000/fman@400000/mdio@e1120/p4080ds-mdio0 has invalid PHY address [ 4.191608] mdio_bus NULL: /soc@ffe000000/fman@400000/mdio@e1120/p4080ds-mdio1 has invalid PHY address [ 4.200888] mdio_bus NULL: /soc@ffe000000/fman@400000/mdio@e1120/p4080ds-mdio2 has invalid PHY address [ 4.210175] mdio_bus NULL: /soc@ffe000000/fman@400000/mdio@e1120/p4080ds-mdio3 has invalid PHY address [ 4.220201] Freescale XGMAC MDIO Bus: probed [ 4.224378] mdio_bus NULL: /soc@ffe000000/fman@400000/mdio@f1000/p4080ds-xmdio1 has invalid PHY address [ 4.233764] mdio_bus NULL: /soc@ffe000000/fman@400000/mdio@f1000/p4080ds-xmdio3 has invalid PHY address [ 4.246311] alloc irq_desc for 25 on node 0 [ 4.250574] alloc kstat_irqs on node 0 [ 4.254492] irq: irq 25 on host /soc@ffe000000/pic@40000 mapped to virtual irq 25 [ 4.263881] audit: initializing netlink socket (disabled) [ 4.269212] type=2000 audit(3.580:1): initialized [ 4.274167] highmem bounce pool size: 64 pages [ 4.278527] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 4.284852] HugeTLB registered 16 MB page size, pre-allocated 0 pages [ 4.291278] HugeTLB registered 64 MB page size, pre-allocated 0 pages [ 4.297698] HugeTLB registered 256 MB page size, pre-allocated 0 pages [ 4.304211] HugeTLB registered 1 GB page size, pre-allocated 0 pages [ 4.317739] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 4.324160] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 4.330777] fuse init (API version 7.13) [ 4.335002] JFS: nTxBlock = 8192, nTxLock = 65536 [ 4.342880] yaffs Nov 29 2017 11:09:44 Installing. [ 4.347696] msgmni has been set to 1367 [ 4.351993] alg: No test for cipher_null (cipher_null-generic) [ 4.357781] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 4.363666] alg: No test for digest_null (digest_null-generic) [ 4.369504] alg: No test for compress_null (compress_null-generic) [ 4.376879] alg: comp: Compression test 1 failed for lzo-generic: output len = 57 [ 4.384305] alg: No test for stdrng (krng) [ 4.388380] io scheduler noop registered [ 4.392262] io scheduler deadline registered [ 4.396709] io scheduler cfq registered (default) [ 4.406444] OOM PROTECT Driver v1.0 [ 4.409914] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 4.416514] serial8250.0: ttyS0 at MMIO 0xffe11c500 (irq = 36) is a 16550A [ 4.423313] console [ttyS0] enabled, bootconsole disabled [ 4.423313] console [ttyS0] enabled, bootconsole disabled [ 4.434222] serial8250.0: ttyS1 at MMIO 0xffe11c600 (irq = 36) is a 16550A [ 4.441258] serial8250.0: ttyS2 at MMIO 0xffe11d500 (irq = 37) is a 16550A [ 4.448295] serial8250.0: ttyS3 at MMIO 0xffe11d600 (irq = 37) is a 16550A [ 4.458104] brd: module loaded [ 4.462530] loop: module loaded [ 4.465982] nbd: registered device at major 43 [ 4.473215] Freescale USDPAA shared memory driver [ 4.477916] fsl-usdpaa-shmem: no region found [ 4.483557] fef800000.flash: Found 1 x16 devices at 0x0 in 16-bit bank [ 4.490096] Amd/Fujitsu Extended Query Table at 0x0040 [ 4.495328] fef800000.flash: CFI does not contain boot bank location. Assuming top. [ 4.502981] number of CFI chips: 1 [ 4.507875] RedBoot partition parsing not available [ 4.512764] Creating 4 MTD partitions on "fef800000.flash": [ 4.518331] 0x000000000000-0x000000010000 : "rcw" [ 4.523403] 0x000000600000-0x000000700000 : "uboot1" [ 4.528661] 0x000000700000-0x000000800000 : "uboot0" [ 4.533874] 0x000000100000-0x000000200000 : "temp" [ 4.539021] slram: not enough parameters. [ 4.543780] bonding: Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) [ 4.551273] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. [ 4.568994] alloc irq_desc for 96 on node 0 [ 4.573348] alloc kstat_irqs on node 0 [ 4.577268] irq: irq 96 on host /soc@ffe000000/pic@40000 mapped to virtual irq 96 [ 4.596618] alloc irq_desc for 97 on node 0 [ 4.600971] alloc kstat_irqs on node 0 [ 4.604901] irq: irq 97 on host /soc@ffe000000/pic@40000 mapped to virtual irq 97 [ 4.645479] Freescale FM module (Nov 29 2017:11:10:10) [ 4.650614] cpu0: fsl_mac: FSL FMan MAC API based driver () [ 4.656404] cpu0: fsl_mac: ffe4e0000.ethernet: mac.c:257:mac_probe() of_get_mac_address(/soc@ffe000000/fman@400000/ethernet@e0000) failed [ 4.668766] fsl_mac: probe of ffe4e0000.ethernet failed with error -22 [ 4.675933] cpu0: fsl_mac: ffe5e0000.ethernet: FMan dTSEC version: 0x08240101 [ 4.683066] cpu0: fsl_mac: ffe5e0000.ethernet: FMan MAC address: 00:11:3f:f8:5b:8a [ 4.691053] cpu0: fsl_mac: ffe5e2000.ethernet: FMan dTSEC version: 0x08240101 [ 4.698195] cpu0: fsl_mac: ffe5e2000.ethernet: FMan MAC address: 00:11:3f:f8:5b:8b [ 4.705903] mac_probe();phy_if= 2, max_speed= 100, line 326, file: drivers/net/dpa/mac.c [ 4.714209] cpu0: fsl_mac: ffe5e4000.ethernet: FMan dTSEC version: 0x08240101 [ 4.721349] cpu0: fsl_mac: ffe5e4000.ethernet: FMan MAC address: 00:11:3f:f8:5b:8c [ 4.729326] cpu0: fsl_mac: ffe5e6000.ethernet: FMan dTSEC version: 0x08240101 [ 4.736468] cpu0: fsl_mac: ffe5e6000.ethernet: FMan MAC address: 00:11:3f:f8:5b:8d [ 4.744188] cpu0: fsl_dpa: FSL DPAA Ethernet driver () [ 4.752844] cpu0: fsl_oh: FSL FMan Offline Parsing port driver () [ 4.759712] tun: Universal TUN/TAP device driver, 1.6 [ 4.764774] tun: (C) 1999-2004 Max Krasnyansky [ 4.771173] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.777752] fsl-ehci platform: Freescale On-Chip EHCI Host Controller [ 4.784287] fsl-ehci platform: new USB bus registered, assigned bus number 1 [ 4.814788] fsl-ehci platform: irq 44, io base 0xffe210000 [ 4.834771] fsl-ehci platform: USB 2.0 started, EHCI 1.00 [ 4.840410] hub usb: USB hub found [ 4.843815] hub usb: 1 port detected [ 4.847825] Initializing USB Mass Storage driver... [ 4.852776] usbcore: registered new interface driver usb-storage [ 4.858789] USB Mass Storage support registered. [ 4.863621] i2c /dev entries driver [ 4.867488] alloc irq_desc for 38 on node 0 [ 4.871842] alloc kstat_irqs on node 0 [ 4.875775] irq: irq 38 on host /soc@ffe000000/pic@40000 mapped to virtual irq 38 [ 4.884929] at24 i2c: 256 byte 24c02 EEPROM (writable) [ 4.891113] at24 i2c: 256 byte 24c02 EEPROM (writable) [ 4.897360] alloc irq_desc for 39 on node 0 [ 4.901713] alloc kstat_irqs on node 0 [ 4.905645] irq: irq 39 on host /soc@ffe000000/pic@40000 mapped to virtual irq 39 [ 4.913940] cfl_i2c_probe(cfl-i2c, pdev->id=0) [ 4.918401] alloc irq_desc for 155 on node 0 [ 4.922840] alloc kstat_irqs on node 0 [ 4.926764] irq: irq 155 on host /bootfpga@fd0000000 mapped to virtual irq 155 [ 4.934180] EDAC MC: Ver: 2.1.0 Nov 29 2017 [ 4.938529] Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software [ 4.945930] mpc85xx_mc_err_probe: No ECC DIMMs discovered [ 4.951480] mpc85xx_mc_err_probe: No ECC DIMMs discovered [ 4.960082] oprofile: using ppc/e500mc performance monitoring. [ 4.966556] u32 classifier [ 4.969261] Netfilter messages via NETLINK v0.30. [ 4.973982] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 4.980343] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 4.987748] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 4.995664] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 5.002082] ctnetlink v0.93: registering with nfnetlink. [ 5.007525] xt_time: kernel timezone is -0000 [ 5.012565] IPv4 over IPv4 tunneling driver [ 5.017339] GRE over IPv4 tunneling driver [ 5.022537] ip_tables: (C) 2000-2006 Netfilter Core Team [ 5.027918] TCP cubic registered [ 5.031141] Initializing XFRM netlink socket [ 5.035517] NET: Registered protocol family 27 [ 5.040473] NET: Registered protocol family 10 [ 5.053405] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 5.060797] NET: Registered protocol family 17 [ 5.065265] NET: Registered protocol family 15 [ 5.069720] 802.1Q VLAN Support v1.8 Ben Greear [ 5.076508] All bugs added by David S. Miller [ 5.083705] SCTP: Hash tables configured (established 65536 bind 43690) [ 5.091091] tipc: Activated (version 2.0.0) [ 5.095600] NET: Registered protocol family 30 [ 5.100040] tipc: Started in single node mode [ 5.104976] Freescale P4080DS MDIO Bus: probed [ 5.109972] mdio_bus NULL: error probing PHY at address 0 [ 5.115730] registered taskstats version 1 [ 5.122108] UBIFS error (pid 1): compr_init: cannot initialize compressor lzo, error -2 [ 5.130121] csd: CSD deadlock debugging initiated! [ 5.165401] usb usb: new high speed USB device using fsl-ehci and address 2 [ 5.321078] scsi0 : usb-storage 1-1:1.0 [ 6.326442] scsi scsi: Direct-Access MICRON eUSB DISK 1112 PQ: 0 ANSI: 0 CCS [ 6.335079] sd scsi: Attached scsi generic sg0 type 0 [ 6.340541] sd scsi: [sda] 7929856 512-byte logical blocks: (4.06 GB/3.78 GiB) [ 6.348285] sd scsi: [sda] Write Protect is off [ 6.352814] sd scsi: [sda] Mode Sense: 43 00 00 00 [ 6.357618] sd scsi: [sda] Assuming drive cache: write through [ 6.364658] sd scsi: [sda] Assuming drive cache: write through [ 6.370502] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > [ 6.380909] sd scsi: [sda] Assuming drive cache: write through [ 6.386787] sd scsi: [sda] Attached SCSI disk [ 6.654830] IP-Config: Complete: [ 6.657881] device=eth2, addr=192.168.10.1, mask=255.255.255.0, gw=255.255.255.255, [ 6.665909] host=192.168.10.1, domain=, nis-domain=(none), [ 6.671827] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 6.679686] SCHEDT#1845 : SCHEDT version 2.5 [ 6.684051] Freeing unused kernel memory: 10004k init init started: BusyBox v1.15.3 (2017-09-19 15:46:34 CST) Mounting and fix partitions.....: the active partition is 0 /dev/sda1: recovering journal /dev/sda1: clean, 61/53760 files, 83054/857180 blocks [ 11.109680] kjournald starting. Commit interval 5 seconds [ 11.111264] EXT3-fs (sda1): using internal journal [ 11.111272] EXT3-fs (sda1): mounted filesystem with writeback data mode /dev/sda2: recovering journal /dev/sda2: clean, 490/90624 files, 194682/1445344 blocks [ 14.142308] kjournald starting. Commit interval 5 seconds [ 14.149124] EXT3-fs (sda2): using internal journal [ 14.153923] EXT3-fs (sda2): mounted filesystem with journal data mode /dev/sda3: recovering journal /dev/sda3: clean, 337/4824 files, 3757/19220 blocks [ 15.564531] kjournald starting. Commit interval 5 seconds [ 15.565867] EXT3-fs (sda3): using internal journal [ 15.565874] EXT3-fs (sda3): mounted filesystem with journal data mode /dev/sda5: clean, 1227/32760 files, 211344/526596 blocks [ 15.672654] kjournald starting. Commit interval 5 seconds [ 15.806616] EXT3-fs (sda5): using internal journal [ 15.811428] EXT3-fs (sda5): mounted filesystem with writeback data mode /dev/sda6: recovering journal [ 15.894765] eth2: no IPv6 routers present /dev/sda6: clean, 1225/32760 files, 211072/526596 blocks (check in 2 mounts) [ 16.408021] kjournald starting. Commit interval 5 seconds [ 16.409738] EXT3-fs (sda6): using internal journal [ 16.409745] EXT3-fs (sda6): mounted filesystem with writeback data mode mount_rmem.sh: start= 0xf5500000 size= 171008 Kb [ 16.842724] pbd0: unknown partition table [ 16.847257] PBD driver v.1.0 Built Nov 29 2017:11:15:49 initialized mount_rmem.sh: Formatting /dev/pbd0 ... PMEM will now being partitioned All Data within will be destroyed Umounting PMEM file systems if already mounted 1+0 records in 1+0 records out Deleted all partitions Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel Building a new DOS disklabel with disk identifier 0x02b36133. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (1-344, default 1): Using default value 1 Last cylinder, +cylinders or +size{K,M,G} (1-344, default 344): Command (m for help): Command action e extended p primary partition (1-4) Partition number (1-4): First cylinder (39-344, default 39): Using default value 39 Last cylinder, +cylinders or +size{K,M,G} (39-344, default 344): Using default value 344 Command (m for help): Command (m for help): The partition table has been altered! Calling ioctl() [ 21.978894] pbd0:to re-read parti p1tion table. p2 Syncing disks. ALL Partitions Created:Proceeding to create jfs Filesystems.... Making jfs filesystem on /dev/pbd0p1 mkfs.jfs version 1.1.15, 04-Mar-2011 Warning! All data on device /dev/pbd0p1 will be lost! Continue? (Y/N) Format completed successfully. 18817 kilobytes total disk space. Making jfs filesystem on /dev/pbd0p2 mkfs.jfs version 1.1.15, 04-Mar-2011 Warning! All data on device /dev/pbd0p2 will be lost! Continue? (Y/N) Format completed successfully. 151776 kilobytes total disk space. mount_rmem.sh: Mounted /rmem using /dev/pbd0p2 mount_rmem.sh: Mounted /rdata using /dev/pbd0p1 [ 30.062320] kbsp: module license 'Proprietary' taints kernel. [ 30.068111] Disabling lock debugging due to kernel taint [ 30.077728] CFL CFL_CPLD_CNTRL register addr 0xf101000c [ 30.083038] Data read before write from CFL_CPLD_CNTRL Register = 0x0 [ 30.089584] Data written into CFL_CPLD_CNTRL Register = 0x50 [ 30.095413] Data read from CFL_CPLD_CNTRL Register = 0x50 [ 30.100908] CFL SYNTH_CTRL register addr 0xf101028c [ 30.105868] Data read before write from SYNTH_CTRL Register = 0xC02B0511 [ 30.112662] Data written into SYNTH_CTRL Register = 0xC0010511 [ 30.118675] Data read from SYNTH_CTRL Register = 0xC0010511 [ 30.124346] bsp loaded (generated Nov 29 2017) [ 30.196881] bsp init by 1436 settimefromsib syslogd started ok crond job started ok Mounting /scd Softlinking atopsar Config loaded 60, 1000, 100.00 file to excute /usr/bin/report_top cpumonit: Cpumonit starting up Child process created: 1545 Softlinking ip Setting Up for strongSwan Softlinking strongswan/gmp update device with mdev! 192.168.10.1 login: [ 33.657629] LEC_SQN=403 [ 34.194618] (null) 1815 kbci_module_ini.. Device major 246, minor 0 [ 34.201281] (null) 1815 bci_register_me.. Registered menu 'klog' [ 34.214183] (null) 1817 klec_module_ini.. Device major 245, minor 0 [ 34.220899] (null) 1817 bci_register_me.. Registered menu '/klec' [ 34.232789] bkhlPhy_k_init: @scFPGA base=0xf100c000 [ 34.237730] bkhlPhy_k_init: disable reset of phy [ 34.242448] bkhlPhy_k_init: IRQ_PHY = 7 [ 34.246401] reset reg addr : f1008024 [ 34.250243] read reset reg value : 1176042f [ 34.254600] changed reset reg value : 1176042f [ 34.259167] re-read reset reg value : 1176042f [ 34.263705] bkhlPhy_k_init: write data 0xF44 to ctrl reg of port 4 [ 34.269996] wait for read complete: [ 34.273661] bkhlphy waiting for access complete. ind value: 0 [ 34.279516] bkhlphy waiting for access complete. i value: 0 [ 34.285201] bkhlPhy_k_init: read of port4 reg 0x15 = 0 [ 34.290431] wait for read complete: [ 34.294088] bkhlphy waiting for access complete. ind value: 0 [ 34.299932] bkhlphy waiting for access complete. j value: 0 [ 34.305606] bkhlPhy_k_init: read of port4 reg 0x15 = 10 [ 34.310920] bkhlPhy_k_init: write 0xF44 to port 5 reg 0x17 [ 34.316514] wait for read complete: [ 34.320184] bkhlphy waiting for access complete. ind value: 0 [ 34.326037] bkhlphy waiting for access complete. k value: 0 [ 34.331698] bkhlPhy_k_init: read of port5 reg 0x15 = 0 [ 34.336944] wait for read complete: [ 34.340614] bkhlphy waiting for access complete. ind value: 0 [ 34.346464] bkhlphy waiting for access complete. m value: 0 [ 34.352126] bkhlPhy_k_init: read of port5 reg 0x15 = 10 [ 34.357458] Out : bkhlPhy_k_init [ 34.360780] bkhlphy loaded: MAJOR= 244 [ 34.368732] bdetect loaded (built date: Nov 29 2017) with major number 243 [ 34.380419] led loaded (generated Nov 29 2017) [ 34.388962] syn: registered with major number:241 [ 34.398419] drvclock: registered with major number:240 [ 34.410855] IHUBdrv:ihub_module_init:#1439 ihub device loading (generated Nov 29 2017) [ 34.422419] IHUBdrv:ihub_probe:#1353 ihub_probe: char device allocated [ 34.428998] IHUBdrv:ihub_probe:#1368 IHUB driver loaded, device class major number = 239 [ 34.443952] uart-fpga loaded (generated Nov 29 2017) MAJOR=238 [ 34.459911] GPSAM driver - version Nov 29 2017 11:16:01 [ 34.465194] eccm bootfpga revision 0.14 (main) [ 34.469652] eccm scfpga revision 0.14 [ 34.473496] eccm #0 (left) is currently active in rack [ 34.478677] gpsam is currently plugged in rack [ 34.483123] GPSAM driver successfully loaded with major 237 [ 34.501290] timeloaded [ 34.524985] (null) 1846 bci_register_me.. Registered menu '/i2c_common' [ 34.531976] i2c_common loaded: I2C Common MAJOR= 235 [ 34.552058] (null) 1848 bci_register_me.. Registered menu '/i2cocxo' [ 34.558817] i2c-ocxo loaded (generated Nov 29 2017) MAJOR=234 [ 34.579203] cpri loaded: MAJOR= 233 [ 34.587184] xcob loaded: MAJOR= 232 [ 34.595018] drvom: registered with major number:231 [ 34.604251] CPMdrv: CPM driver Built Nov 29 2017:11:18:01 [ 34.630538] pktstat driver: Nov 29 2017 11:16:40 [ 34.635258] create an entry in /proc for pktstat = c0ebbf80 [ 34.640940] create an entry in /proc for pktstat 1 = ecade000 [ 34.646810] create an entry in /proc for pktstat 2 = ecade080 [ 34.652653] create an entry in /proc for pktstat 3 = ecade100 [ 34.658531] create an entry in /proc for pktstat 4 = ecade180 [ 34.664378] create an entry in /proc for pktstat 5 = ecade280 [ 34.670244] create an entry in /proc for pktstat 6 = ecade200 [ 34.676104] create an entry in /proc for pktstat 7 = ecade300 [ 34.681935] create an entry in /proc for pktstat 8 = ecade380 [ 34.687787] create an entry in /proc for pktstat 9 = ecade400 [ 34.693617] create an entry in /proc for pktstat 10 = ecade480 [ 34.699564] create an entry in /proc for pktstat 11 = ecade500 [ 34.705511] create an entry in /proc for pktstat 12 = ecade600 [ 34.711442] create an entry in /proc for pktstat 13 = ecade580 [ 34.717387] create an entry in /proc for pktstat 14 = ecade680 [ 34.723304] create an entry in /proc for pktstat 15 = ecade700 [ 34.841748] (null) 1877 klec_ioctl.. New registered process [ 34.870610] device eth3 entered promiscuous mode [ 34.883710] tipc: Started in network mode [ 34.887743] tipc: Own node address <1.1.1>, network identity 4711 [ 34.893929] tipc: Enabled bearer , discovery domain <1.1.0>, priority 10 [ 35.451626] WDDI mmap driver - version Nov 29 2017 11:16:12 [ 35.457559] mmapdrv_pci_probe on card 0: 1980:0003 0000:0000 (eccm2) [ 35.463968] region 0 is mem [ 35.470101] PCI memory 0xc80000000 size 0x800000 [ 35.474835] region 2 is mem [ 35.477722] PCI memory 0xca0000000 size 0x20000000 [ 35.482624] region 4 is mem [ 35.485446] PCI memory 0xcc0000000 size 0x40000000 [ 35.490737] region 0 virt addr at 0xfdf00000, size 0x800000 [ 35.496614] (siu3/siu3i Int'l RAM/RIF at 0x80000000 (0xfdf00000, 0x800000 bytes) Region 0 [ 35.504794] (siu4D-DDRC at 0xa0000000 (0x00000000, 0x20000000 bytes) Region 2 [ 35.506214] (null) 1924 kbci_open.. Task registered [ 35.507263] (null) 1924 kbci_open.. Task registered [ 35.514218] (null) 1922 kbci_open.. Task registered [ 35.515903] (null) 1922 kbci_open.. Task registered [ 35.534953] (siu1/siu2-DDRA/B) at 0xc0000000 (0x00000000, 0x40000000 bytes) Region 4 [ 35.542744] mmap_handle->wp at fe300000 [ 35.546586] mmap_handle->wp_ram_addr at fdf00000 [ 35.549427] (null) 1930 kbci_open.. Task registered [ 35.549727] (null) 1930 kbci_open.. Task registered [ 35.562699] mmap_handle = 0xef052c00, mmap_handle->wp = 0xfe300000, mmap_handle->wp_ram_addr = 0xfdf00000 [ 35.572283] create serial qs event kfifo stuff [ 35.576746] init_waitqueue_head for qs_fifo_proc_list [ 35.581883] create serial op event kfifo stuff [ 35.586351] create op fifo list [ 35.586674] (null) 1922 klec_ioctl.. New registered process [ 35.587033] (null) 1924 klec_ioctl.. New registered process [ 35.597272] (null) 1934 kbci_open.. Task registered [ 35.598132] (null) 1934 kbci_open.. Task registered [ 35.610026] (null) 1930 klec_ioctl.. New registered process [ 35.620032] create sys fifo list [ 35.623345] create serial sgmii event kfifo stuff [ 35.628081] init_waitqueue_head for sgmii_fifo_proc_list [ 35.633479] start for wp3 hw init() [ 35.637191] wpath3_hw_init() wp is at 0xfe300000 wp_u = 0xfe300000 [ 35.643380] next calling run_init_code() [ 35.656556] (null) 1931 kbci_open.. Task registered [ 35.665160] (null) 1934 klec_ioctl.. New registered process [ 35.672465] (null) 1931 kbci_open.. Task registered [ 35.684141] (null) 1925 kbci_open.. Task registered [ 35.690921] (null) 1925 kbci_open.. Task registered [ 35.719331] (null) 1931 klec_ioctl.. New registered process [ 35.750776] (null) 1925 klec_ioctl.. New registered process [ 36.371298] wpath3_hw_init() next calling init_ecc() [ 36.390293] (null) 1935 kbci_open.. Task registered [ 36.390341] (null) 1932 kbci_open.. Task registered [ 36.390715] (null) 1933 kbci_open.. Task registered [ 36.391167] (null) 1932 kbci_open.. Task registered [ 36.391392] (null) 1933 kbci_open.. Task registered [ 36.395331] (null) 1928 kbci_open.. Task registered [ 36.403575] (null) 1928 kbci_open.. Task registered [ 36.410657] (null) 1923 kbci_open.. Task registered [ 36.411425] (null) 1923 kbci_open.. Task registered [ 36.413223] (null) 1929 kbci_open.. Task registered [ 36.414153] (null) 1926 kbci_open.. Task registered [ 36.419049] (null) 1926 kbci_open.. Task registered [ 36.419324] (null) 1929 kbci_open.. Task registered [ 36.419907] (null) 1927 kbci_open.. Task registered [ 36.420671] (null) 1927 kbci_open.. Task registered [ 36.454001] init_ecc_part(addr= 1ec00000, end_addr= 1eea0000, size=2a0000) [ 36.455852] (null) 1932 klec_ioctl.. New registered process [ 36.455907] (null) 1933 klec_ioctl.. New registered process [ 36.457872] (null) 1928 klec_ioctl.. New registered process [ 36.462612] init_ecc_part(addr= c0000000, end_addr= e0000000, size=20000000) [ 36.471965] (null) 1923 klec_ioctl.. New registered process [ 36.480429] bsp init by 1930 cpmcallp [ 36.480443] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 36.480446] BSPECCM_IOC_Q_RESET return 113 [ 36.480793] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 36.480798] BSPECCM_IOC_Q_RESET return 113 [ 36.481731] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 36.481751] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 36.481755] BSPECCM_IOC_Q_RESET return 113 [ 36.485924] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 36.489970] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 36.489974] BSPECCM_IOC_Q_RESET return 113 [ 36.491231] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 36.503159] (null) 1929 klec_ioctl.. New registered process [ 36.503453] (null) 1927 klec_ioctl.. New registered process [ 36.503724] (null) 1926 klec_ioctl.. New registered process [ 36.528114] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 36.528118] BSPECCM_IOC_Q_RESET return 113 [ 36.529356] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 36.577576] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 36.577580] BSPECCM_IOC_Q_RESET return 113 [ 36.578827] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 36.624603] (null) 1935 kbci_open.. Task registered [ 36.632150] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 36.681179] (null) 1935 klec_ioctl.. New registered process [ 37.258393] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.263457] BSPECCM_IOC_Q_RESET return 113 [ 37.267553] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.272612] BSPECCM_IOC_Q_RESET return 113 [ 37.276706] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.281755] BSPECCM_IOC_Q_RESET return 113 [ 37.285854] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.292052] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.298246] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.303296] BSPECCM_IOC_Q_RESET return 113 [ 37.307401] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.321607] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.326667] BSPECCM_IOC_Q_RESET return 113 [ 37.334765] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.339821] BSPECCM_IOC_Q_RESET return 113 [ 37.343918] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.350118] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.355166] BSPECCM_IOC_Q_RESET return 113 [ 37.363345] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.370810] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.387997] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 37.490131] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 37.495183] BSPECCM_IOC_Q_RESET return 113 [ 37.500672] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 38.126893] init_ecc_part(addr= 40000000, end_addr= 60000000, size=20000000) [ 39.797495] init_ecc_part(addr= 80000000, end_addr= a0000000, size=20000000) [ 41.467891] init_ecc() ECC is enabled, good [ 41.472635] next calling WPX_BoardSerdesInit() [ 41.477425] WPX_BoardSerdesInit() next initing port 0 rate 0 serdes 2 lane_index 2 [ 41.485208] WPX_SerdesSetQuadLane() init-- serdes 2 lane 2 rate 0 loopback_mode 0x0 base 0xfe308280 [ 41.494437] WPX_SerdesInit_1_G_QuadLane() init regaddr 0xfe308280 ioctrl at 0xfe3082a0 serdes 2 lane 2 [ 41.615420] WPX_SerdesSetQuadLane() init done -- serdes 2 rate 0 [ 41.621427] WPX_BoardSerdesInit() next initing port 2 rate 0 serdes 3 lane_index 1 [ 41.629010] WPX_SerdesSetQuadLane() init-- serdes 3 lane 1 rate 0 loopback_mode 0x0 base 0xfe308280 [ 41.638065] WPX_SerdesInit_1_G_QuadLane() init regaddr 0xfe308280 ioctrl at 0xfe3082b8 serdes 3 lane 1 [ 41.731172] SCHEDT#1672 : Schedt monitoring mode set by 1922/1922 [ 41.765393] WPX_SerdesSetQuadLane() init done -- serdes 3 rate 0 [ 41.771395] WPX_BoardSerdesInit() next initing port 4 rate 0 serdes 4 lane_index 1 [ 41.778973] WPX_SerdesSetQuadLane() init-- serdes 4 lane 1 rate 0 loopback_mode 0x0 base 0xfe308280 [ 41.788027] WPX_SerdesInit_1_G_QuadLane() init regaddr 0xfe308280 ioctrl at 0xfe3082d0 serdes 4 lane 1 [ 41.915389] WPX_SerdesSetQuadLane() init done -- serdes 4 rate 0 [ 41.921392] WPX_BoardSerdesInit() next initing port 6 rate 0 serdes 2 lane_index 0 [ 41.928966] WPX_SerdesSetQuadLane() init-- serdes 2 lane 0 rate 0 loopback_mode 0x0 base 0xfe308280 [ 41.938015] WPX_SerdesInit_1_G_QuadLane() init regaddr 0xfe308280 ioctrl at 0xfe3082a0 serdes 2 lane 0 [ 42.063338] OOM_PROTECT: Process 1922 registered by OOM killer [ 42.075393] WPX_SerdesSetQuadLane() init done -- serdes 2 rate 0 [ 42.078542] OOM_PROTECT: Process 1925 registered by OOM killer [ 42.087231] WPX_BoardSerdesInit() next initing port 12 rate 0 serdes 3 lane_index 3 [ 42.094884] WPX_SerdesSetQuadLane() init-- serdes 3 lane 3 rate 0 loopback_mode 0x0 base 0xfe308280 [ 42.103937] WPX_SerdesInit_1_G_QuadLane() init regaddr 0xfe308280 ioctrl at 0xfe3082b8 serdes 3 lane 3 [ 42.225389] WPX_SerdesSetQuadLane() init done -- serdes 3 rate 0 [ 42.231392] WPX_BoardSerdesInit() next initing port 14 rate 0 serdes 4 lane_index 3 [ 42.239053] WPX_SerdesSetQuadLane() init-- serdes 4 lane 3 rate 0 loopback_mode 0x0 base 0xfe308280 [ 42.248104] WPX_SerdesInit_1_G_QuadLane() init regaddr 0xfe308280 ioctrl at 0xfe3082d0 serdes 4 lane 3 [ 42.375389] WPX_SerdesSetQuadLane() init done -- serdes 4 rate 0 [ 42.381390] next calling kwddi_wp3_hw_init() [ 42.385664] kwddi_wp3_hw_init() enter wp = 0xfe300000 [ 42.390882] Initializing interrupt controller ic_intmode before = 000016db [ 42.397848] Initializing interrupt controller ic_intmode = 000016db [ 42.411504] Enabled ECC and cleared PRAM for WinFarm 0, wf_ecc_config = 0x300 @ 0xfe306458 [ 42.427166] Enabled ECC and cleared PRAM for WinFarm 1, wf_ecc_config = 0x300 @ 0xfe306558 [ 42.442826] Enabled ECC and cleared PRAM for WinFarm 2, wf_ecc_config = 0x300 @ 0xfe306658 [ 42.458490] Enabled ECC and cleared PRAM for WinFarm 3, wf_ecc_config = 0x300 @ 0xfe306758 [ 42.466763] Clear reset bits for SRIO2(13), SRIO1(12), PCIereset(11), Ext_norm(8), WDo Reset(3),RSTSRCE(2-0) rs_source = 00000000 [ 42.478755] serdes Mux Ctrl 0x273cfefc [ 42.482506] serdes Mux Ctrl 0xefb [ 42.485840] serdes 2 IO Ctrl_1 0x5638000 [ 42.489759] serdes 2 IO Ctrl_2 0x5638000 [ 42.493676] serdes 2 IO Ctrl_3 0x5638000 [ 42.497608] serdes 2 IO Ctrl_4 0x5638000 [ 42.501526] serdes 3 IO Ctrl_1 0x5638000 [ 42.505456] serdes 3 IO Ctrl_2 0x5638000 [ 42.509375] serdes 3 IO Ctrl_3 0x5638000 [ 42.513292] serdes 3 IO Ctrl_4 0x5638000 [ 42.517222] serdes 4 IO Ctrl_1 0x5638000 [ 42.521140] serdes 4 IO Ctrl_2 0x5638000 [ 42.525057] serdes 4 IO Ctrl_3 0x5638000 [ 42.528987] serdes 4 IO Ctrl_4 0x5638000 [ 42.532907] serdes 2 IO Ctrl_0 0x50000 [ 42.536664] serdes 3 IO Ctrl_0 0x50000 [ 42.540409] serdes 4 IO Ctrl_0 0x50000 [ 42.544155] serdes 2 tpll/rpll io_Stat 0x171f1 [ 42.548607] serdes 3 tpll/rpll io_Stat 0x1171f [ 42.553047] serdes 4 tpll/rpll io_Stat 0x11111 [ 42.557586] serdes 2 "ports to BCM switch rx locked status" bits 0x171f1 [ 42.564371] serdes 3 "BH3-bit10 and BH4-bit3 rx locked status " bits 0x1171f [ 42.571602] serdes 4 "BH1-bit3 and BH2-bit10 rx locked status " bits not ok 0x11111 [ 42.579267] serdes 4 "BH1-bit3 and BH2-bit10 rx locked status " bits 0x11111 [ 42.586413] kwddi_wp3_hw_init: set FMU_GMR1 register = 0x2, addr = 0xfe30a2b0 [ 42.593543] kwddi_wp3_hw_init() done [ 42.597211] request irq for pci device [ 42.617871] irq (20) handler installed for INT4. dev->irq 42 [ 42.623526] $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$444 [ 42.628328] $$$ wp->siu.siu4d.siu_reg_arb_config1_ddr = 7a77 [ 42.633982] $$$ wp->siu.siu1.siu_reg_arb_config1_ddr = 7a77 [ 42.639560] $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$4 [ 42.644519] =========================================================== [ 42.651137] start test internal RAM [ 42.654706] internal RAM kaddr = fdf00000 [ 42.658719] ----------------------------------------------------------- [ 42.676412] *(testRamPtr) = 0 [ 42.679465] *(testRamPtr + 1) = 1 [ 42.682862] *(testRamPtr + 2) = 2 [ 42.686268] *(testRamPtr + 3) = 3 [ 42.689664] *(testRamPtr + 0x1000) = 1000 [ 42.693754] *(testRamPtr + 0x1004) = 1004 [ 42.697863] *(testRamPtr + 0x1008) = 1008 [ 42.701955] *(testRamPtr + 0x17FF4) = 17ff4 [ 42.706230] *(testRamPtr + 0x17FF8) = 17ff8 [ 42.710495] *(testRamPtr + 0x17FFC) = 17ffc [ 42.714758] ***********Internal RAM check finished************* [ 42.720680] *************************************************************** [ 42.727646] Clear reset bits for SRIO2(13), SRIO1(12), PCIereset(11), Ext_norm(8), WDo Reset(3),RSTSRCE(2-0) rs_source = 00000000 [ 42.739302] wp->irpt.ic_intmode = 16db [ 42.743045] wp->irpt.ic_interupt_l = 8000000 [ 42.747318] wp->irpt.ic_interupt_h = 0 [ 42.751062] wp->irpt.ic_sw_int = 0 [ 42.754459] wp->irpt.ic_mask_pin_l = 7ffffff [ 42.758732] wp->irpt.ic_mask_pin_h = 7ffffe7f [ 42.763084] wp->irpt.ic_sw_int now is = 1 [ 42.767097] wp->irpt.ic_intmode = 16db [ 42.770841] wp->irpt.ic_interupt_l = 18000000 [ 42.775193] wp->irpt.ic_interupt_h = 8 [ 42.778944] wp->irpt.ic_sw_int = 1 [ 42.782342] wp->irpt.ic_mask_pin_l = 7ffffff [ 42.786615] wp->irpt.ic_mask_pin_h = 7ffffe7f [ 42.790966] ######################################################## [ 42.797324] wp->irpt.ic_sw_int now is = 3 [ 42.801328] wp->irpt.ic_intmode = 16db [ 42.805071] wp->irpt.ic_interupt_l = 18000000 [ 42.809432] wp->irpt.ic_interupt_h = 18 [ 42.813262] wp->irpt.ic_sw_int = 3 [ 42.816668] wp->irpt.ic_mask_pin_l = 7ffffff [ 42.820933] wp->irpt.ic_mask_pin_h = 7ffffe7f [ 42.825284] ######################################################## [ 42.831641] wp->irpt.ic_sw_int now is = 7 [ 42.835654] wp->irpt.ic_intmode = 16db [ 42.839397] wp->irpt.ic_interupt_l = 18000000 [ 42.843749] wp->irpt.ic_interupt_h = 40018 [ 42.847848] wp->irpt.ic_sw_int = 7 [ 42.851244] wp->irpt.ic_mask_pin_l = 7ffffff [ 42.855522] wp->irpt.ic_mask_pin_h = 7ffffe7f [ 42.859873] ######################################################## [ 42.866231] wp->irpt.ic_sw_int now is = f [ 42.870236] wp->irpt.ic_intmode = 16db [ 42.873979] wp->irpt.ic_interupt_l = 18000000 [ 42.878339] wp->irpt.ic_interupt_h = c0018 [ 42.882430] wp->irpt.ic_sw_int = f [ 42.885834] wp->irpt.ic_mask_pin_l = 7ffffff [ 42.890099] wp->irpt.ic_mask_pin_h = 7ffffe7f [ 42.894450] ######################################################## [ 42.900811] wp->siu.siu3.siu3_reg_config = 0x60000000 [ 42.905868] siu1.siu_reg_gen_config = 0x40024000 [ 42.910915] siu1.siu_reg_ecc_dbg = 0x0 [ 42.915353] siu1.siu_reg_ecc_cntr = 0x0 [ 42.919801] siu2.siu_reg_gen_config = 0x40024000 [ 42.924849] siu2.siu_reg_ecc_dbg = 0x0 [ 42.929295] siu2.siu_reg_ecc_cntr = 0x0 [ 42.933733] siu3_reg_ecc_debug_conf0 = 0x600000 [ 42.938615] siu3_reg_ecc_debug_conf1 = 0x0 [ 42.943054] siu3_reg_ecc_error_counter = 0x0 [ 42.947502] siu4d.siu_reg_gen_config = 0x40024000 [ 42.952549] siu4d.siu_reg_ecc_dbg = 0x0 [ 42.956995] siu4d.siu_reg_ecc_cntr = 0x0 [ 42.961601] mmap_drv:hid0 is: x80000080 [ 43.124777] SW INTERRPT: ic_ir_h = c0018 ic_ir_l = 0 [ 43.129832] SW INTERRPT: ic_interupt_h c0018 ic_interupt_l 18000000 mask_pin_h 7ff3fe67 mask_pin_l 7ffffff [ 43.340533] (null) 2214 kbci_open.. Task registered [ 43.362850] (null) 2213 kbci_open.. Task registered [ 43.375668] (null) 2214 kbci_open.. Task registered [ 43.385056] (null) 2213 kbci_open.. Task registered [ 43.392142] (null) 2215 kbci_open.. Task registered [ 43.398338] (null) 2215 kbci_open.. Task registered [ 43.422343] (null) 2211 kbci_open.. Task registered [ 43.428504] (null) 2211 kbci_open.. Task registered [ 43.431612] linux-kernel-bde (2239): _interrupt_connect d 0 _d 0 [ 43.431618] linux-kernel-bde (2239): connect primary isr [ 43.432122] (null) 2213 klec_ioctl.. New registered process [ 43.432411] (null) 2214 klec_ioctl.. New registered process [ 43.454496] (null) 2215 klec_ioctl.. New registered process [ 43.484310] (null) 2211 klec_ioctl.. New registered process [ 43.523896] OOM_PROTECT: Process 1927 registered by OOM killer [ 43.834451] OOM_PROTECT: Process 1934 registered by OOM killer [ 44.004854] OOM_PROTECT: Process 1935 registered by OOM killer [ 44.236053] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 44.241105] BSPECCM_IOC_Q_RESET return 113 [ 44.245417] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 44.250465] BSPECCM_IOC_Q_RESET return 113 [ 44.256782] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 44.261830] BSPECCM_IOC_Q_RESET return 113 [ 44.267073] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 44.278272] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 44.289984] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 44.296192] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 44.301241] BSPECCM_IOC_Q_RESET return 113 [ 44.309352] Data read from CFL SYNTH PLL LOCK STATUS = 0xc0010511 [ 44.518841] OOM_PROTECT: Process 1930 registered by OOM killer [ 44.564386] OOM_PROTECT: Process 2215 registered by OOM killer [ 44.608581] OOM_PROTECT: Process 2214 registered by OOM killer [ 44.670962] OOM_PROTECT: Process 2213 registered by OOM killer [ 45.975464] bdetect opened by 1923 pltf [ 45.979326] mate_want_activity opened by 1923 pltf [ 45.984127] switch_activity opened by 1923 pltf [ 46.060891] OOM_PROTECT: Process 1932 registered by OOM killer [ 46.066730] OOM_PROTECT: Process 1933 registered by OOM killer [ 46.127320] OOM_PROTECT: Process 1931 registered by OOM killer [ 46.203762] OOM_PROTECT: Process 2211 registered by OOM killer [ 46.223028] led init by 1923 pltf [ 46.289110] OOM_PROTECT: Process 1926 registered by OOM killer [ 48.151638] OOM_PROTECT: Process 1924 registered by OOM killer [ 49.452263] it_scFpga_stspps_init : INIT_IRQ_SYN_STSPPS, it_number= 1 [ 49.459000] it_scFpga_init : INIT_IRQ_SYN_STSMDA, it_number= 3 [ 49.465110] it_scFpga_init : INIT_IRQ_SYN_STSPCM, it_number= 2 [ 49.489200] WARN: i2c_slot1_isr#902: i2c_k_isr irq=158, empty work queue [ 52.273594] tipc: Established link <1.1.1:eth3-1.1.2:eth1.1> on network plane A [ 52.922764] tipc: Established link <1.1.1:eth3-1.1.3:eth1.1> on network plane A [ 54.484784] WARN: _i2c_write_interrupt#3443: _i2c_write_interrupt() timeout [ 54.493792] i2cmodem1-bootloader#3459 pid=1923 >>> EIO [ 56.101376] i2c-ocxo In : i2c_ocxo_init [ 56.101379] [ 56.106659] i2c-ocxo In : i2c_ocxo_init @Virtual base= 0xf100c000 [ 56.113106] i2c-ocxo In : i2c_ocxo_init *uboot_version= 0x0e000c00 [ 56.119465] i2c-ocxo In : i2c_ocxo_init *uboot_test_reg= 0x55555555 [ 56.125859] i2c-ocxo In : i2c_ocxo_init *uboot_test_reg= 0x55555555 [ 56.132432] i2c-ocxoOut : i2c_ocxo_init [ 56.137105] it_scFpga_init : INIT_IRQ_SYN_TIMER, it_number= 1 [ 56.143214] it_scFpga_init : INIT_IRQ_SYN_PCMHVR, it_number= 2 [ 56.154081] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'irq_syn_stspps' [ 56.162749] IHUBdrv:ihub_irq_subscribe:#1073 IRQ resource irq_syn_stspps will be request_irq [ 56.171385] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource irq_syn_stspps instatiated [ 58.443725] virt_utime as returned by irq_of_parse_and_map 21 [ 58.449588] virt_utime as returned by irq_of_parse_and_map 21 [ 58.455437] virt_utime as returned by irq_of_parse_and_map 21 [ 58.495306] time: req_irq even second 21 not registered = 0xfffffff0 [ 58.501683] time: req_irq even second 21 not registered = 0xfffffff0 [ 59.325377] In : i2c_gpsam_hw_init [ 59.328867] in : i2c_gpsam_hw_init @Virtual base= 0xf1008000 [ 59.334609] in : i2c_gpsam_hw_init Physical addr= 0xd0000000 [ 59.340369] in : i2c_gpsam_hw_init *pt_boot_revtyp_reg = 0x000c000e [ 59.346898] in : i2c_gpsam_hw_init *pt_boot_test_reg = 0xaaaaaaaa [ 59.353421] in : i2c_gpsam_hw_init *pt_reset_control_reg = 0x1176042f [ 59.359953] in : i2c_gpsam_hw_init *pt_reset_control_reg = 0x1176042f [ 59.366481] i2c gpsam hw init : 0x0 [ 59.380392] SCHEDT#1672 : Schedt monitoring mode set by 1922/2188 [ 59.462170] bspk_bootfpga_get_curr_bootid = 0 [ 59.642158] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'int_gps_stat' [ 59.657331] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource int_gps_stat instatiated [ 59.702544] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'ext_gps_stat' [ 59.748632] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource ext_gps_stat instatiated [ 60.905023] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'syce1_stat' [ 60.915777] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource syce1_stat instatiated [ 60.928585] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'syce2_stat' [ 60.937231] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource syce2_stat instatiated [ 60.955001] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'syce3_stat' [ 60.964102] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource syce3_stat instatiated [ 60.985016] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'syce4_stat' [ 60.993408] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource syce4_stat instatiated [ 61.476072] BSPECCM_IOC_Q_RESET get reason 0x00000071 [ 61.481128] BSPECCM_IOC_Q_RESET return 113 [ 61.485365] IHUBdrv:ihub_irq_subscribe:#1036 Got subscription request for irq 'sys_pps' [ 61.522696] IHUBdrv:ihub_irq_subscribe:#1073 IRQ resource sys_pps will be request_irq [ 61.563999] IHUBdrv:ihub_irq_subscribe:#1101 IRQ resource sys_pps instatiated [ 61.628095] read POWER CPLD version reg 0 [ 61.632113] CFL power version register addr f1010180 [ 61.637172] Data read from CFL Power Version Register = 0xC07 [ 61.756289] OOM_PROTECT: Process 1923 registered by OOM killer [ 65.078909] GPS bit write in CFL pwer control reg 30 [ 65.083875] Data read from CFL Power control Register before writting the data = 0x3B [ 65.091810] Data written into CFL power control Register = 0x3B [ 65.097909] Data read from CFL Power control Register = 0x3B [ 92.337494] pktstat_ioctl: PKTSTAT_SET_BP_IPS wpPdcpIp 0xc0a83004, modemIp 0xc0a85004 [ 92.751930] FAULT:wpPfnIndex:x00000005, maxIndex:x00000001 [ 92.757436] va:x60000000, pfn:x00cc0000, address:x60000000 [ 92.762917] VxTLB-1:basePhysAddr : 0xc0000000 [ 92.767271] VxTLB-2:basePhysAddr : 0xc0000000 [ 92.771622] mfspr(SPRN_PID) : 0xd3 [ 92.775017] VTLB-3:basePhysAddr : 0xcc0000000 [ 92.779374] vxTLB1:pte_user(x0054303d) TRUE [ 92.783551] vxTLB1:MAS0, x10050006 [ 92.786949] vxTLB1:MAS1, xc0d30900 [ 92.790344] vxTLB1:MAS2, x6000000a [ 92.793739] vxTLB1:MAS3, xc000003f [ 92.797137] vxTLB1:MAS7, x0000000c [ 92.800532] vxTLB1:pte_user(x0054303d) TRUE [ 92.804708] vxTLB1:MAS0, x10060007 [ 92.808106] vxTLB1:MAS1, xc0d30900 [ 92.811502] vxTLB1:MAS2, x7000000a [ 92.814897] vxTLB1:MAS3, xd000003f [ 92.818296] vxTLB1:MAS7, x0000000c [ 92.821765] FAULT:wpPfnIndex:x00000007, maxIndex:x00000002 [ 92.827253] va:x80000000, pfn:x00ce0000, address:x80000000 [ 92.832732] VxTLB-1:basePhysAddr : 0xe0000000 [ 92.837087] VxTLB-2:basePhysAddr : 0xe0000000 [ 92.841436] mfspr(SPRN_PID) : 0xd3 [ 92.844831] VTLB-3:basePhysAddr : 0xce0000000 [ 92.849187] vxTLB1:pte_user(x0054303d) TRUE [ 92.853364] vxTLB1:MAS0, x10070008 [ 92.856763] vxTLB1:MAS1, xc0d30900 [ 92.860158] vxTLB1:MAS2, x8000000a [ 92.863553] vxTLB1:MAS3, xe000003f [ 92.866952] vxTLB1:MAS7, x0000000c [ 92.870347] vxTLB1:pte_user(x0054303d) TRUE [ 92.874523] vxTLB1:MAS0, x10080009 [ 92.877921] vxTLB1:MAS1, xc0d30900 [ 92.881316] vxTLB1:MAS2, x9000000a [ 92.884713] vxTLB1:MAS3, xf000003f [ 92.888111] vxTLB1:MAS7, x0000000c [ 93.074372] FAULT:wpPfnIndex:x00000003, maxIndex:x00000003 [ 93.079860] va:x20000000, pfn:x00ca0001, address:x20001000 [ 93.085340] VxTLB-1:basePhysAddr : 0xa0000000 [ 93.089693] VxTLB-2:basePhysAddr : 0xa0000000 [ 93.094043] mfspr(SPRN_PID) : 0xd3 [ 93.097441] VTLB-3:basePhysAddr : 0xca0000000 [ 93.101794] vxTLB1:pte_user(x0154303d) TRUE [ 93.105971] vxTLB1:MAS0, x10030004 [ 93.109369] vxTLB1:MAS1, xc0d30900 [ 93.112765] vxTLB1:MAS2, x2000000a [ 93.116162] vxTLB1:MAS3, xa000003f [ 93.119557] vxTLB1:MAS7, x0000000c [ 93.122952] vxTLB1:pte_user(x0154303d) TRUE [ 93.127132] vxTLB1:MAS0, x10040005 [ 93.130528] vxTLB1:MAS1, xc0d30900 [ 93.133922] vxTLB1:MAS2, x3000000a [ 93.137321] vxTLB1:MAS3, xb000003f [ 93.140716] vxTLB1:MAS7, x0000000c [ 97.358734] CPMdrv: CPM_ALLOC_DEV eb060000 4 [ 97.365674] CPMdrv: CPM_ALLOC_DEV eb070000 4 [ 105.840330] device eth0 entered promiscuous mode [ 105.844989] device eth0 left promiscuous mode [ 106.196406] pktstat_ioctl: PKTSTAT_SET_MINPKTSZ_LIMIT. nopadding min sz set to 42 [ 106.203978] pktstat_ioctl: PKTSTAT_SET_GTPECHOPORT. gtp port set to 2152 [ 106.210702] pktstat_ioctl: PKTSTAT_SET_SCTPPORT. sctp port set to 36422 [ 106.217334] pktstat_ioctl: PKTSTAT_ADD_INTF. intf eth0.5 trfMap 1 [ 106.223431] pktstat_ioctl: PKTSTAT_SET_ETH_IPVADDR interface eth0.5 addr 114.20.82.42 trafType 1 count 1 [ 108.718236] pktstat_ioctl: PKTSTAT_ADD_INTF. intf eth0.4 trfMap 2 [ 108.724339] pktstat_ioctl: PKTSTAT_SET_ETH_IPVADDR interface eth0.4 addr 10.209.78.42 trafType 2 count 1 [ 108.736848] pktstat_ioctl: PKTSTAT_ADD_INTF. intf eth0.4 trfMap 2 [ 108.742942] pktstat_ioctl: PKTSTAT_SET_ETH_IPVADDR interface eth0.4 addr 10.209.78.42 trafType 4 count 2 [ 108.752544] pktstat_ioctl: PKTSTAT_ADD_INTF. intf eth0.4 trfMap 2 [ 108.758653] pktstat_ioctl: PKTSTAT_SET_ETH_IPVADDR interface eth0.4 addr 10.209.78.42 trafType 2 count 3 [ 108.768227] pktstat_ioctl: PKTSTAT_ADD_INTF. intf eth0.4 trfMap 2 [ 108.774318] pktstat_ioctl: PKTSTAT_SET_ETH_IPVADDR interface eth0.4 addr 10.209.78.42 trafType 10 count 4 [ 109.068391] pktstat_ioctl: PKTSTAT_SET_PKT_DSCP(ICMP). dscp 0xb0 [ 109.358787] pktstat_ioctl: PKTSTAT_SET_PKT_DSCP(IKEv2). dscp 0xb8 [ 110.404880] FAULT:wpPfnIndex:x00000005, maxIndex:x00000004 [ 110.410379] va:x60000000, pfn:x00ccb6de, address:x6b6de000 [ 110.415862] VxTLB-1:basePhysAddr : 0xc0000000 [ 110.420213] VxTLB-2:basePhysAddr : 0xc0000000 [ 110.424562] mfspr(SPRN_PID) : 0xd3 [ 110.427962] VTLB-3:basePhysAddr : 0xcc0000000 [ 110.432316] vxTLB1:pte_user(xde54303d) TRUE [ 110.436497] vxTLB1:MAS0, x10050006 [ 110.439891] vxTLB1:MAS1, xc0d30900 [ 110.443286] vxTLB1:MAS2, x6000000a [ 110.446684] vxTLB1:MAS3, xc000003f [ 110.450079] vxTLB1:MAS7, x0000000c [ 110.453475] vxTLB1:pte_user(xde54303d) TRUE [ 110.457654] vxTLB1:MAS0, x10060007 [ 110.461049] vxTLB1:MAS1, xc0d30900 [ 110.464444] vxTLB1:MAS2, x7000000a [ 110.467842] vxTLB1:MAS3, xd000003f [ 110.471237] vxTLB1:MAS7, x0000000c [ 110.474675] FAULT:wpPfnIndex:x00000007, maxIndex:x00000005 [ 110.480165] va:x80000000, pfn:x00cf7ab7, address:x97ab7580 [ 110.485649] VxTLB-1:basePhysAddr : 0xe0000000 [ 110.490000] VxTLB-2:basePhysAddr : 0xe0000000 [ 110.494350] mfspr(SPRN_PID) : 0xd3 [ 110.497750] VTLB-3:basePhysAddr : 0xce0000000 [ 110.502103] vxTLB1:pte_user(xb754303d) TRUE [ 110.506283] vxTLB1:MAS0, x10070008 [ 110.509678] vxTLB1:MAS1, xc0d30900 [ 110.513074] vxTLB1:MAS2, x8000000a [ 110.516472] vxTLB1:MAS3, xe000003f [ 110.519867] vxTLB1:MAS7, x0000000c [ 110.523263] vxTLB1:pte_user(xb754303d) TRUE [ 110.527443] vxTLB1:MAS0, x10080009 [ 110.530839] vxTLB1:MAS1, xc0d30900 [ 110.534234] vxTLB1:MAS2, x9000000a [ 110.537633] vxTLB1:MAS3, xf000003f [ 110.541028] vxTLB1:MAS7, x0000000c