early_board_init : gS8400_flag is S8400_CPU [GPIO rx_dat_val : 0x0FE7DFFC] [GPIO device ID : 0x00000000] [S8400] DSP#0 uPbaId : 0x5051, uDbir : 0x6f U-Boot 2015.00 (Development build, svnversion: u-boot:exported, exec:) (Build time: Jul 09 2018 - 06:44:33) Octeon unique ID: 00800090811df31e0148 DRAM SCRAMBLE enable by default DRAM SCRAMBLE DATA KEY set by 0xaaaaaaaaaaaaaaaa DDR2T enabled rtt_park_00 set to 3(60ohm) LPASR set to 3 N0.LMC0.R0: Rlevel Rank 0x1, FINAL SETTINGS : 11 13 13 12 12 11 11 11 11 Enable Preserve mode during soft/warm reset(interface_num:0, lmc_reset_ctl: 0x7) GD_FLG_MEMORY_PRESERVED flag cleared N0.LMC0 Configuration Completed: 2048 MB DRAM SCRAMBLE enable by default DRAM SCRAMBLE DATA KEY set by 0xaaaaaaaaaaaaaaaa DDR2T enabled rtt_park_00 set to 3(60ohm) LPASR set to 3 N0.LMC1.R0: Rlevel Rank 0x1, FINAL SETTINGS : 12 13 13 12 12 11 11 11 11 Enable Preserve mode during soft/warm reset(interface_num:1, lmc_reset_ctl: 0x7) GD_FLG_MEMORY_PRESERVED flag cleared N0.LMC1 Configuration Completed: 2048 MB Warning: Board descriptor tuple not found in eeprom, using defaults LCC_M board revision major:1, minor:0, serial #: unknown OCTEON CNF7560-AAP pass 1.2, Core clock: 1600 MHz, IO clock: 800 MHz, DDR clock: 1067 MHz (2134 Mhz DDR) get_hw_diagnostic_flag : 0x0 Base DRAM address used by u-boot: 0x10f000000, size: 0x1000000 DRAM: 4 GiB *********************** debug_level is (LOW) *********************** Clearing DRAM...... Rewrite LOADABLE OS area , done [GPIO rx_dat_val : 0x0FE7DFFC] [GPIO device ID : 0x00000000] [S8400] DSP#0 uPbaId : 0x5051, uDbir : 0x6f Bootbus #0 reconfig for temporary Reserved Memory for Loadable OS [board_init_r:2007]LoadableOS Flag[0x2de00010]:0x514d2e4f AllocFlag:0x00000000 Reserved Memory for MEMLOG Flash: 256 MiB ISL6398 READ 0xD6(0x3)ISL6398 READ 0xDA(0x7c)ISL6398 READ 0x10(0x80)-0x70.0...OK ISL6398 READ 0xD6(0x3)ISL6398 READ 0xDA(0x7c)ISL6398 READ 0x10(0x80)-0x70.1...OK ISL6398 READ 0xD6(0x3)ISL6398 READ 0xDA(0x7c)ISL6398 READ 0x10(0x80)-0x70.2...OK PROTECTION MODE : POWER OFF [TEMP INFO] Board:22`C, CPU:30`C (T:9) [TEMP INFO] FPGA Local:23`C, Remote:23`C (T:10) [TEMP INFO] DSP #1 Local:22`C, Remote:30`C (T:10) [TEMP INFO] DSP #2 Local:22`C, Remote:30`C (T:9) Set Temperature Alert Function 0xc1(0xc1)!! Check the High Temperature for Board Protection CDCM7005 PLL Lock Status:6 try_count:1 CDCM7005 PLL Lock Status:6 try_count:2 CDCM7005 PLL Lock Status:6 try_count:3 CDCM7005 PLL Lock Status:6 try_count:4 CDCM7005 PLL Lock Status:6 try_count:5 CDCM7005 PLL Lock Status:6 try_count:6 CDCM7005 PLL Lock Status:6 try_count:7 CDCM7005 PLL Lock Status:6 try_count:8 CDCM7005 PLL Lock Status:6 try_count:9 CDCM7005 PLL Lock Status:6 try_count:10 CDCM7005 PLL Lock Status:6 try_count:11 CDCM7005 PLL Lock Status:6 try_count:12 CDCM7005 PLL Lock Status:6 try_count:13 CDCM7005 PLL Lock Status:6 try_count:14 CDCM7005 PLL Lock Status:6 try_count:15 Skipping PCI init PCI console output has been enabled. Initializing PCI console with count 1, size 200000 PCI console init succeeded, 1 consoles, 2097152 bytes each LCC_M board revision major:1, minor:0, serial #: unknown OCTEON CNF7560-AAP pass 1.2, Core clock: 1600 MHz, IO clock: 800 MHz, DDR clock: 1067 MHz (2134 Mhz DDR) Net: Phy not found PHY reset timed out for Generic 10G PHY (devad: -1, reg: 0xffff) octeth0, octeth1, octeth2, octeth3 FPGA Done bit not set! FPGA Reset for Loading (addr:0x21->0x1) FPGA_FW_MODE is 2 Loading SECOND FPGA Image Find TAILER in FPGA Image at 0xd2000000 mkimage header FPGA load_addr[0x20000040] BOOTCMD:[unzip 0x20000040 0x24000000 ] Uncompressed size: 48251520 = 0x2E04280 Xilinx fpga load addr = 0x24000000 Configuring target FPGA via Slave SelectMAP Bitstream start address in memory = 0x24000000 Bitstream size in bytes = 0x02E04280 FPGA Type : IFPGA Downloading Bitstream to target FPGA ................................ Downloading Complete [SUCCESS]FPGA image loading! FPGA Reset Release for PCI enumeration (addr:0x21->0x0) Type the command 'usb start' to scan for USB storage devices. Board will reset after 60 second unless you input 'watchdog disable' Hit CTRL-C key to stop autoboot: 0 get_hw_diagnostic_flag : 0x0 Total Core Num:16 CoreNumOfSE :15 MemSzOfSE :2944 LoadableOS Flag[0x2de00010] : 0x514d2e4f(MagicNum:0xb1a4d00d) Try:0xa96d7553 NamedAllocFlag : 0x00000000 ** kernel A image check Image Name: Linux Created: 2018-12-16 18:10:58 UTC Image Type: MIPS Linux Kernel Image (gzip compressed) Data Size: 3402101 Bytes = 3.2 MiB Load Address: 00000000 Entry Point: 00000000 ** kernel A image check passed ** rfs A image check Image Name: Additional RFS Created: 2018-11-14 2:40:42 UTC Image Type: MIPS Linux RAMDisk Image (gzip compressed) Data Size: 14230999 Bytes = 13.6 MiB Load Address: 00000000 Entry Point: 00000000 ** rfs A image check passed ** booting with kernel A, rfs A CMD_FLASH_KERNEL : gunzip 0x18000040 0x21000000 CMD_BOOT_LINUX : bootoctlinux 0x21000000 coremask=0x00000001 console=ttyS0,115200 rd_start=0x86000000 rd_size=0x02800000 rw mem=1152M ip=off $(RUNLEVEL) A A rhash_entries=8192 __BOO Uncompressed size: 8410576 = 0x8055D0 Allocating memory for ELF segment: addr: 0xffffffff80800000 (adjusted to: 0x800000), size 0x99b670 ## Loading big-endian Linux kernel with entry point: 0xffffffff80d0e570 ... Bootloader: Done loading app on coremask: 0x1 Starting cores: 0x1 [ 0.000000] Linux version 3.10.94.cge-rt102 (ci_lte@ea-rhel6-06) (gcc version 4.7.0 (MontaVista Linux G++ 4.7-151105191608) ) #0 SMP Mon Dec 17 03:07:27 KST 2018 [ 0.000000] GPIO_RX_DAT : 0xc7dcfd [ 0.000000] S8400 Type : CPU + Modem, CPLD info get from bootbus [ 0.000000] _MemorySize_OF_SE(2944MB) [ 0.000000] RESERVE_FOR_SE_TEMP at 0x50000000(2944MB) [ 0.000000] CVMSEG size: 3 cache lines (384 bytes) [ 0.000000] Cavium Inc. SDK-3.1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 000d9802 (Cavium Octeon III) [ 0.000000] FPU revision is: 00739800 [ 0.000000] Checking for the multiply/shift bug... no. [ 0.000000] Checking for the daddiu bug... no. [ 0.000000] RESERVE_FOR_SE_TEMP freed [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0000000000400000 @ 0000000000400000 (usable) [ 0.000000] memory: 00000000007c2000 @ 0000000000800000 (kernel data and code) [ 0.000000] memory: 000000000004e000 @ 0000000000fc2000 (usable after init) [ 0.000000] memory: 000000000018c000 @ 0000000001010000 (kernel data and code) [ 0.000000] memory: 000000000e400000 @ 0000000001200000 (usable) [ 0.000000] memory: 0000000000400000 @ 000000000fb00000 (usable) [ 0.000000] memory: 000000000c000000 @ 0000000020000000 (usable) [ 0.000000] memory: 000000001fc00000 @ 0000000030200000 (usable) [ 0.000000] Initial ramdisk at: 0x8000000006000000 (41943040 bytes) [ 0.000000] Using passed Device Tree <800000000ffd1be0>. [ 0.000000] plat_swiotlb_setup 321 WA to use more than 8GB [ 0.000000] software IO TLB [mem 0x02010000-0x02050000] (0MB) mapped at [8000000002010000-800000000204ffff] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x00400000-0xefffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00400000-0x0119bfff] [ 0.000000] node 0: [mem 0x01200000-0x0f5fffff] [ 0.000000] node 0: [mem 0x0fb00000-0x0fefffff] [ 0.000000] node 0: [mem 0x20000000-0x2bffffff] [ 0.000000] node 0: [mem 0x30200000-0x4fdfffff] [ 0.000000] Primary instruction cache 78kB, virtually tagged, 39 way, 16 sets, linesize 128 bytes. [ 0.000000] Primary data cache 32kB, 32-way, 8 sets, linesize 128 bytes. [ 0.000000] Secondary unified cache 4096kB, 16-way, 2048 sets, linesize 128 bytes. [ 0.000000] PERCPU: Embedded 10 pages/cpu @8000000002069000 s12160 r8192 d20608 u40960 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 238766 [ 0.000000] Kernel command line: bootoctlinux 0x21000000 coremask=0x00000001 console=ttyS0,115200 rd_start=0x86000000 rd_size=0x02800000 rw ip=off A A rhash_entries=8192 __BOOTUP_5 [ 0.000000] get __BOOTUP_FLAG__ : 0000 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Memory: 900560k/958776k available (5298k kernel code, 58216k reserved, 2642k data, 312k init, 0k highmem) [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=16, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=48 to nr_cpu_ids=16. [ 0.000000] NR_IRQS:511 [ 0.000000] Console: colour dummy device 80x25 [ 36.087572] Calibrating delay loop (skipped) preset value.. 3200.00 BogoMIPS (lpj=6400000) [ 36.095781] pid_max: default: 32768 minimum: 501 [ 36.100553] Mount-cache hash table entries: 256 [ 36.105951] Checking for the daddi bug... no. [ 36.110131] [MEMLOG] memlog actual size : 0x976868 [ 36.114918] [MEMLOG] memlog area is allocated in the booter 0x2000000 @ 0x2e000000 [ 36.122457] [MEMLOG] cold reset [ 36.125580] [MEMLOG] memlog disabled at loadable romos mode [ 36.131139] [UFH] PBA_ID: 5051 DBIR : 0x6f CPU: 0 [ 36.135911] [UFH] Initialized [ 36.140162] Brought up 1 CPUs [ 36.143352] devtmpfs: initialized [ 36.150472] NET: Registered protocol family 16 [ 36.154776] kworker/u32:0 (15) used greatest stack depth: 14248 bytes left [ 36.162554] Error: No error tree for prid = 0x000d9802 [ 36.172395] PCIe: Initializing port 0:0 [ 36.892377] PCIe: Port 0 link active, 1 lanes, speed gen2 [ 37.001736] PCIe: Initializing port 0:1 [ 37.721726] PCIe: Port 1 link active, 2 lanes, speed gen2 [ 37.833448] kworker/u32:0 (55) used greatest stack depth: 13896 bytes left [ 37.848784] bio: create slab at 0 [ 37.853404] SCSI subsystem initialized [ 37.857520] EDAC MC: Ver: 3.0.0 [ 37.861075] PCI host bridge to bus 0000:00 [ 37.865037] pci_bus 0000:00: root bus resource [mem 0x1000000000000] [ 37.871401] pci_bus 0000:00: root bus resource [io 0x0000] [ 37.876896] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 37.884934] PCI host bridge to bus 0000:01 [ 37.888899] pci_bus 0000:01: root bus resource [mem 0x11b00f0000000-0x11b0fffffffff] (bus address [0xf0000000-0xfffffffff]) [ 37.900042] pci_bus 0000:01: root bus resource [io 0x1000-0xffffffff] [ 37.906494] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 38.259744] pci 0000:01:00.0: of_irq_parse_pci() failed with rc=-22 [ 38.265953] pci 0000:01:00.0: BAR 2: assigned [mem 0x11b00f0000000-0x11b00f3ffffff 64bit pref] [ 38.334454] pci 0000:01:00.0: BAR 4: assigned [mem 0x11b00f4000000-0x11b00f47fffff 64bit pref] [ 38.402906] pci 0000:01:00.0: BAR 0: assigned [mem 0x11b00f4800000-0x11b00f48fffff 64bit pref] [ 38.471496] PCI host bridge to bus 0001:02 [ 38.475445] pci_bus 0001:02: root bus resource [mem 0x11c00f0000000-0x11c0fffffffff] (bus address [0xf0000000-0xfffffffff]) [ 38.486534] pci_bus 0001:02: root bus resource [io 0x100000000-0x1ffffffff] (bus address [0x0000-0xffffffff]) [ 38.496511] pci_bus 0001:02: No busn resource found for root bus, will use [bus 02-ff] [ 38.939697] pci 0001:02:00.0: of_irq_parse_pci() failed with rc=-22 [ 38.945904] pci 0001:02:00.0: BAR 0: assigned [mem 0x11c00f0000000-0x11c00f0ffffff] [ 38.999078] Switching to clocksource OCTEON_CVMCOUNT [ 39.011130] NET: Registered protocol family 2 [ 39.015811] TCP established hash table entries: 8192 (order: 5, 131072 bytes) [ 39.022940] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 39.029369] TCP: Hash tables configured (established 8192 bind 8192) [ 39.035702] TCP: reno registered [ 39.038844] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 39.044757] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 39.051319] NET: Registered protocol family 1 [ 39.055637] copy ramdisk from flash:0xffffffffb9400040 size:0x19a6891 [ 40.802116] octeon_pci_console: Initialized. [ 40.806406] /proc/octeon_perf: Octeon performance counter interface loaded [ 40.813198] uncore: uncore: uncore_mc counters detected [ 40.818400] uncore: uncore: uncore_l2c counters detected [ 40.823637] uncore: uncore: uncore_tad counters detected [ 40.829138] unaligned_action set to UNALIGNED_ACTION_SIGNAL(1) [ 40.860534] MIN_FREE : 9005KB (Total RAM : 900560KB, LOW_MEM : 900564KB) [ 40.879450] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 40.886398] msgmni has been set to 1758 [ 40.890546] io scheduler noop registered [ 40.894301] io scheduler deadline registered [ 40.898836] io scheduler cfq registered (default) [ 40.903501] octeon_gpio 1070000000800.gpio-controller: OCTEON GPIO: base = 0 [ 40.910580] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 40.916165] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 40.923069] init debug port on/off proc [ 40.926820] init SIGINT on/off proc [ 40.930537] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 64) is a OCTEON [ 40.938375] console [ttyS0] enabled, bootconsole disabled [ 40.938375] console [ttyS0] enabled, bootconsole disabled [ 40.949349] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 369) is a OCTEON [ 40.957762] octeon_rng octeon_rng: Octeon Random Number Generator [ 40.964302] brd: module loaded [ 40.969641] loop: module loaded [ 40.975045] libphy: mdio-octeon: probed [ 40.979808] mdio-octeon 1180000003800.mdio: Version 1.0 [ 40.985287] i2c /dev entries driver [ 40.988885] cn78xx_style disabled [ 40.992454] [octeon_i2c_probe:1703] I2C Bus Time Out : 52 ms [ 40.998286] i2c-octeon 1180000001000.i2c: version 2.6 [ 41.004216] cn78xx_style disabled [ 41.007666] [octeon_i2c_probe:1703] I2C Bus Time Out : 52 ms [ 41.013565] i2c-octeon 1180000001100.i2c: version 2.6 [ 41.019436] cn78xx_style disabled [ 41.022967] [octeon_i2c_probe:1703] I2C Bus Time Out : 52 ms [ 41.028808] i2c-octeon 1180000001200.i2c: version 2.6 [ 41.034008] octeon_wdt: Initial granularity 4 Sec [ 41.039223] EDAC DEVICE0: Giving out device to module 'octeon-cpu' controller 'cache': DEV 'octeon_pc_edac' (INTERRUPT) [ 41.050146] EDAC DEVICE1: Giving out device to module 'octeon-l2c' controller 'octeon_l2c_err': DEV 'octeon_l2c_edac' (POLLED) [ 41.061805] EDAC MC0: Giving out device to 'octeon-lmc' 'co_lmc_err': DEV octeon_lmc_edac.0 [ 41.070342] EDAC MC1: Giving out device to 'octeon-lmc' 'co_lmc_err': DEV octeon_lmc_edac.1 [ 41.155981] CP:Probing 0x08000000 at 0x17c00000 [ 41.160589] Octeon64 Flash Bank #0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 41.171470] Amd/Fujitsu Extended Query Table at 0x0040 [ 41.177626] Amd/Fujitsu Extended Query version 1.5. [ 41.182680] number of CFI chips: 1 [ 41.186088] CP:Probing 0x08000000 at 0x10000d0000000 [ 41.191099] Octeon64 Flash Bank #1: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 41.201977] Amd/Fujitsu Extended Query Table at 0x0040 [ 41.207127] Amd/Fujitsu Extended Query version 1.5. [ 41.212179] number of CFI chips: 1 [ 41.215581] CP:Using Booter0 partition definition [ 41.220285] Creating 23 MTD partitions on "Octeon64 Flash Bank #0": [ 41.226553] 0x000000000000-0x000000200000 : "Booter0" [ 41.232130] 0x000000200000-0x000000400000 : "Rsvd" [ 41.237441] 0x000000400000-0x000000e00000 : "KERNEL0" [ 41.243019] 0x000000e00000-0x000001800000 : "KERNEL1" [ 41.248614] 0x000001800000-0x000004000000 : "RFS_Raw" [ 41.254195] 0x000004000000-0x000005700000 : "RFS0" [ 41.259524] 0x000005700000-0x000006e00000 : "RFS1" [ 41.264856] 0x000006e00000-0x000007600000 : "HW_Test" [ 41.270445] 0x000007600000-0x000007a00000 : "DSP_DBG" [ 41.276076] 0x000007b00000-0x000007f00000 : "UFH" [ 41.281321] 0x000007f00000-0x000007f60000 : "Rsvd_1" [ 41.286821] 0x000007fa0000-0x000007fc0000 : "ENV" [ 41.292094] 0x000007fc0000-0x000007fe0000 : "ENV_R" [ 41.297517] 0x000007fe0000-0x000008000000 : "IM" [ 41.302684] 0x000000000000-0x000008000000 : "flash0" [ 41.308252] 0x000007f60000-0x000007f80000 : "SECU_FILES" [ 41.314099] 0x000007f80000-0x000007fa0000 : "SECU_FILES_R" [ 41.320151] 0x000007a40000-0x000007a60000 : "SECU_KEY" [ 41.325832] 0x000007a60000-0x000007a80000 : "SECU_VENDOR" [ 41.331783] 0x000007a80000-0x000007aa0000 : "SECU_OPERATOR" [ 41.337899] 0x000007aa0000-0x000007ac0000 : "SECU_KEY_R" [ 41.343757] 0x000007ac0000-0x000007ae0000 : "SECU_VENDOR_R" [ 41.349814] 0x000007ae0000-0x000007b00000 : "SECU_OPERATOR_R" [ 41.356079] CP:Using FPGA partition definition [ 41.360530] Creating 5 MTD partitions on "Octeon64 Flash Bank #1": [ 41.366749] 0x000000000000-0x000002000000 : "FPGA" [ 41.372027] 0x000002000000-0x000004000000 : "CFPGA0" [ 41.377471] 0x000004000000-0x000006000000 : "IFPGA1" [ 41.382921] 0x000006000000-0x000008000000 : "CFPGA1" [ 41.387936] kworker/u32:0 (687) used greatest stack depth: 13776 bytes left [ 41.395360] 0x000000000000-0x000008000000 : "flash1" [ 41.400795] Init Lowpri Debugging Extension. [ 41.405160] [UFH] UFH driver init. [ 41.408672] [UFH] SW reason : 0x00 [ 41.412164] [UFH] HW reason : 0x01 [ 41.415648] [UFH] Status : 0x14009ce1 [ 41.419396] [UFH] RST_BOOT : 0x0800000810000004 [ 41.824020] [UFH] set_reset_reason(): 0x1f -> 0x00 [ 41.828900] [ 41.828900] [NPU:Master][Core0] Unit Fault Handler !!! (INDEX=45), TYPE(12:COLD_RESET) RRR:0x01 Status:0x14009ce1 MIO:0x0800000810000004 [ 41.828900] [ 41.844113] Core 0 got ufh_lock [ 42.247256] [UFH] set_reset_reason(): 0x80 -> 0x80 [ 42.252129] UFH: Detecting CPU heart beat... done. [ 42.256927] create_mi: Collecting mortem information... [ 42.262189] Current: swapper/0 (1) [ 42.265863] Serial Num: [ 42.268313] [write_container 2299] UNKNOWN UNKNOWN 0x00000000 0x00000000 0x0000000000000000 0x00000000 0x00000000 0x0000000000000000 [ 42.281086] [UFH] Write Mortem [ 42.292744] MORTEM info size: 64552 Bytes [ 43.125436] [UFH] set_reset_reason(): 0x00 -> 0x00 [ 43.130314] Clear RST_BOOT_LBOOT :0x0800000810000000 [ 43.135276] [POST_DD] post dd init!! [ 43.138859] [POST_DD] writeDeviceStatus is success(name : CPU, status : 0, reason : , dev_num_choice : 0). [ 43.148515] [POST_DD] writeDeviceStatus is success(name : FLASH, status : 0, reason : , dev_num_choice : 1). [ 43.158342] [POST_DD] writeDeviceStatus is success(name : MEMORY, status : 0, reason : , dev_num_choice : 2). [ 43.168256] [MEMLOG] mortem does not save on memlog at romos mode [ 43.174348] Disable Idle Longrun IRQ [ 43.177998] oprofile: using timer interrupt. [ 43.182445] ipip: IPv4 over IPv4 tunneling driver [ 43.187547] ip_tables: (C) 2000-2006 Netfilter Core Team [ 43.192970] TCP: cubic registered [ 43.196292] Initializing XFRM netlink socket [ 43.201205] NET: Registered protocol family 10 [ 43.206173] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 43.211687] NET: Registered protocol family 17 [ 43.216153] NET: Registered protocol family 15 [ 43.220597] 8021q: 802.1Q VLAN Support v1.8 [ 43.227163] sctp: Hash tables configured (established 65536 bind 65536) [ 43.234248] L2 lock: TLB refill 256 bytes [ 43.238270] L2 lock: General exception 128 bytes [ 43.242888] L2 lock: low-level interrupt 128 bytes [ 43.247678] L2 lock: interrupt 640 bytes [ 43.251616] L2 lock: memcpy 1152 bytes [ 43.255444] Bootbus flash: Setting flash for 128MB flash at 0x17c00000 [ 43.262044] phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 43.272483] Amd/Fujitsu Extended Query Table at 0x0040 [ 43.277630] Amd/Fujitsu Extended Query version 1.5. [ 43.282682] number of CFI chips: 1 [ 43.287568] RAMDISK: gzip image found at block 0 [ 45.092546] VFS: Mounted root (ext2 filesystem) on device 1:0. [ 45.103982] devtmpfs: mounted [ 45.107036] Freeing unused kernel memory: 312K (ffffffff80fc2000 - ffffffff81010000) INIT: version 2.88 booting [ 45.152279] mount (726) used greatest stack depth: 12528 bytes left [ 45.168796] cat (728) used greatest stack depth: 11952 bytes left [ 45.175433] awk (730) used greatest stack depth: 11776 bytes left check loadableos lrwxrwxrwx 1 root root 34 Sep 1 2016 /usr/bin/loadingos -> ../local/cptools/OUL/loadingos.ohm Error opening device file No such file or directory kexec_mode:OFF Flash OS cmdline 10 : A [Additional RFS] Magic No:0x27051956, Size:0xd925d7 Len : 14230999 [RFS A] Passed in rfscheck [RFS] Passed in rfscheck uncompress file 0000AA A [ 48.038126] tar (758) used greatest stack depth: 11672 bytes left tar zxfmo /root/RFS.tgz -C /RFS ok copy file RFS mount complete net.ipv4.ip_forward = 1 net.ipv4.conf.default.rp_filter = 0 kernel.sysrq = 1 INIT: Entering runlevel: 5 Flash OS < os_running_mode > rom Starting OpenBSD Secure Shell server: sshd generating ssh RSA key... No supported. xinetd daemon start sshd Make directory under /mnt/CPSW/ for log afile Start the reset_kernel [1970/01/01_00:00:11] Starting syslog-ng:32 signal handler is not registered! 33 signal handler is not registered! . Makedev..... flash link setting... FPGA flash link setting. Start /etc/init.d/rc [Loading /lib/modules/standard/CDH/cpld_ctrl.ko.ohm ] [ 49.471970] Loading CDH Main Driver ... [ 49.475813] SHELF_ID=0x02 [ 49.478444] [cdh] : intiCPLD_Slot[432] > NOTICE : SLOT_ID=0x01 [ 49.484280] [cdh] : CDHMainInit[3753] > NOTICE : Cpu Id = 0 [ 49.489856] PBA ID=0x5051, CPLD Size=0xff, IPC Addressing Type=30 [ 49.503924] CPLD Device registered with Major Number = 253 [ 49.509415] CPLD register_ufh function [ 49.515922] [POST_DD] writeDeviceStatus is success(name : Ctrl_CPLD, status : 0, reason : , dev_num_choice : 3). generating ssh ECDSA key... [ 49.535943] [POST_DD] writeDeviceStatus is success(name : FPGA, status : 0, reason : , dev_num_choice : 4). generating ssh DSA key... [ 49.555932] [POST_DD] writeDeviceStatus is success(name : Clock_CPLD, status : 0, reason : , dev_num_choice : 5). [Loading /lib/modules/standard/CDH/env_ctrl.ko.ohm ] [ 49.583995] uPbaId = 5051 [ 49.586614] pfFlag = 1, gLoadableFlag = 1 [ 49.590633] env : Loading Driver [ 49.621951] case 0 : all good [ 49.624926] [env] : load_flash_config[3863] > WARNING : CRC Check Success !!! (0) [ 49.632411] env : BOOT_FLAG: (0000 0000AA) --> BOOT_FLAG: 0000 0000AA [ 49.651927] [env] : init_proc_env[4219] > NOTICE : OS_VER ENV Nmae is not found. [ 49.996122] [env] : env_init[4591] > ERR : init_proc_env is called [Loading /lib/modules/standard/CDH/im_ctrl.ko.ohm ] [ 50.011945] im : Loading Driver [ 50.016208] im : minor 0x10 [ 50.026042] im SerialNum:[S614319764] [Loading /lib/modules/standard/CDH/cpuload_avg_ctrl.ko.ohm ] [ 50.044173] register_ufh function [Loading /lib/modules/standard/CDH/cmd_his_ctrl.ko.ohm ] [ 50.051956] cmdhis : Loading Command History Device Driver [ 50.058612] cmdhis : minor 22 Error MDM_CPLD_GetFanType: Invalid argument Fail : cmd4rc --printFanType [Loading /lib/modules/standard/CDH/led_ctrl.ko.ohm ] [ 50.123954] LED: Loading Module [ 50.127096] CPRI LED init [Loading /lib/modules/standard/CDH/epld_info_ctrl.ko.ohm ] [ 50.139949] Loading Device Driver [ 50.144937] minor 17 [Loading /lib/modules/standard/CDH/pca9548_ctrl.ko.ohm ] [ 50.159975] [pca954x] : PCA9548Device_init[1165] > NOTICE : Loading Device Driver [ 50.175926] [POST_DD] writeDeviceStatus is success(name : PCA9548, status : 0, reason : , dev_num_choice : 6). [ 50.196125] [POST_DD] DD(PCA9548) is already saved(PCA9548(6)). So overwrite. [ 50.203268] pca954x 0-0070: pca9548 client created (1) [ 50.216132] [POST_DD] DD(PCA9548) is already saved(PCA9548(6)). So overwrite. [ 50.223274] pca954x 0-0071: pca9548 client created (2) [ 50.236134] [POST_DD] DD(PCA9548) is already saved(PCA9548(6)). So overwrite. [ 50.243278] pca954x 0-0072: pca9548 client created (3) [Loading /lib/modules/standard/CDH/optic_ctrl.ko.ohm ] [ 50.264060] optic : Loading Device Driver [ 50.272022] [POST_DD] writeDeviceStatus is success(name : OPTIC, status : 0, reason : , dev_num_choice : 7). [Loading /lib/modules/standard/CDH/tmp461_ctrl.ko.ohm ] [ 50.303967] tmp461_0 : Loading Device Driver [ 50.311927] [POST_DD] writeDeviceStatus is success(name : Temp_Sensor, status : 0, reason : , dev_num_choice : 8). [ 50.332329] tmp461_0 1-004a: tmp461 client created [ 50.344325] tmp461_0 1-004b: tmp461 client created [ 50.356324] tmp461_0 1-004c: tmp461 client created [ 50.368337] tmp461_0 1-004e: tmp461 client created [Loading /lib/modules/standard/CDH/ltc4151_ctrl.ko.ohm ] [ 50.387964] ltc4151 0-006f: ltc4151 client created (1) [ 50.393113] ltc4151 : LTC4151 version 2.0 (20130308) [ 50.400134] [POST_DD] writeDeviceStatus is success(name : LTC4151, status : 0, reason : , dev_num_choice : 9). [Loading /lib/modules/standard/NET/mvKernelExt.ko.ohm ] [Loading /lib/modules/standard/NET/mvIntDrv.ko.ohm ] [Loading /lib/modules/standard/NET/mvDmaDrv.ko.ohm ] [Loading /lib/modules/standard/NET/octeon3-nexus.ko.ohm ] [ 50.464028] [CEDD] pdev->name : 11800e0000000.ethernet-mac-nexus [ 50.476059] octeon3_nexus 11800e0000000.ethernet-mac-nexus: Created PKI 0: 800000004f459600 [ 50.495955] octeon3_nexus 11800e0000000.ethernet-mac-nexus: Created PKI 1: 800000004f459a00 [ 50.512047] octeon3_nexus 11800e0000000.ethernet-mac-nexus: Created PKI 2: 800000004f459e00 [ 50.528047] octeon3_nexus 11800e0000000.ethernet-mac-nexus: Created PKI 3: 800000004f45a200 [ 50.543926] octeon3_nexus 11800e0000000.ethernet-mac-nexus: Probed [Loading /lib/modules/standard/NET/octeon3-bgx.ko.ohm ] [ 50.563992] phy handle for bgx 0 port 0 is not found [ 50.568968] 2048 is MIXED. [ 50.571672] [CEDD-SGMII-CHECK] setting SERDES to autonego off [ 50.577428] octeon3_bgx 11800e0000000.0.ethernet-mac: Probed 0-0 [ 50.587940] phy handle for bgx 0 port 1 found [ 50.592306] 2064 is MIXED. [ 50.595010] [CEDD-SGMII-CHECK] setting SGMII to autonego on [ 50.600589] octeon3_bgx 11800e0000000.1.ethernet-mac: Probed 0-1 [ 50.611938] phy handle for bgx 0 port 2 is not found [ 50.616911] 2080 is MIXED. [ 50.869628] octeon3_bgx 11800e0000000.2.ethernet-mac: Probed 0-2 [ 50.879934] phy handle for bgx 0 port 3 is not found [ 50.884902] 2096 is MIXED. [ 51.137618] octeon3_bgx 11800e0000000.3.ethernet-mac: Probed 0-3 [Loading /lib/modules/standard/NET/octeon3-ethernet.ko.ohm.novidd ] [ 51.211224] Customer TPID is not set. [ 51.217365] [CEDD] Checking board info [ 51.221115] - Shelf_id : 2 [ 51.223908] - Slot_id : 1 [ 51.226612] - VIDD Support : 0 [ 51.229753] - Use Nested VLAN : 0 [ 51.233153] - POW2 send group : 15 [ 51.236728] - Zarlink1588 support : 0 [ 51.240765] The dev num of cedd is : 240 [ 51.244758] zlTsPkts : Device registered with Major Number = 155 [ 51.250773] ethernet driver proc init start [ 51.255773] octeon3_eth_global_init SSO:1:1, PKO:2:2 [ 51.264442] ethernet-mac-pki ethernet-mac-pki.0: Probing 0-0:0 [ 51.270437] ethernet-mac-pki ethernet-mac-pki.0: rx sso grp:1..2 aura:3 pknd:0 pko_queue:1 [ 51.278839] netif_napi_add() called with weight 128 on device eth0 [ 51.285504] ethernet-mac-pki ethernet-mac-pki.0 eth0: Registered [ 51.291623] ethernet-mac-pki ethernet-mac-pki.1: Probing 0-0:1 [ 51.297581] ethernet-mac-pki ethernet-mac-pki.1: rx sso grp:2..3 aura:3 pknd:1 pko_queue:9 [ 51.306289] ethernet-mac-pki ethernet-mac-pki.1 eth1: Registered [ 51.312403] ethernet-mac-pki ethernet-mac-pki.2: Probing 0-0:2 [ 51.318358] ethernet-mac-pki ethernet-mac-pki.2: rx sso grp:3..4 aura:3 pknd:2 pko_queue:17 [ 51.327154] ethernet-mac-pki ethernet-mac-pki.2 xaui0: Registered [ 51.333354] ethernet-mac-pki ethernet-mac-pki.3: Probing 0-0:3 [ 51.339310] ethernet-mac-pki ethernet-mac-pki.3: rx sso grp:4..5 aura:3 pknd:3 pko_queue:25 [ 51.348121] ethernet-mac-pki ethernet-mac-pki.3 xaui1: Registered [READ] CPLD Value (0x4008fd77-0x77) : 0x00 [WRITE] CPLD Value [0x8008fd77-0x77] : 0x00 Check whether /mnt/CPSW dir needs to be remounted with tmpfs filesystem. The CPSW_TMPFS_SIZE of LCC4 is 150M /mnt/CPSW is remounted with tfmpfs filesystem to 150M Remount return value : 0 /pkg directory is linked at /mnt/ram/pkg Hostname: 116_02_01_LCC4_0.<<< networking.common [start] start >>> [ 51.496624] device eth0 entered promiscuous mode [ 51.511542] eth0: Link is not ready [ 51.515051] eth0: Link is up - 1000/Full [ 51.532544] device eth0.1 entered promiscuous mode [ 51.554416] device eth0.2 entered promiscuous mode [ 51.570025] device eth0.99 entered promiscuous mode [ 51.608086] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready === networking.common [start] done === SECURITY_CONFIG: Start /etc/init.d/rc with SECURITY LEVEL [1] id: gid 501 Sat Jan 1 00:00:00 UTC 2000 changed group of '/var/log/btmp' from root to utmp /etc/rc5.d/S62security.sh: line 76: /etc/init.d/xinet_filter.sh: No such file or directory /etc/rc5.d/S62security.sh: line 77: /etc/init.d/secure_backup.sh: No such file or directory No supported. init start crond cp -f /usr/sbin/cbash /bin/bash Stop the reset_kernel [2000/01/01_00:00:00] [ 52.604105] eth1: Link is up - 1000/Full [ 52.618169] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready Start initialization procedure : Start initializing MVDD. Found marvell device 11ab:c81e Configuring aldrin... [ 52.983873] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 53.192012] mvIntDrv_open(file=800000000063c500) /dev/mvIntDrv opened, use interrupts from HW [ 53.309614] MSI interrupts for device 0000:01:00.0 enabled BAR1: win0_ctrl = 0x03ff0031, win_base = 0xf0000000 BAR2: win1_ctrl = 0x000f0083, win_base = 0xf4000000 BAR2: win2_ctrl = 0x000000a3, win_base = 0xf4400000 BAR2: win3_ctrl = 0x000000a3, win_base = 0xf4410000 Configuring DMA... [ 53.343918] mvDmaDrv_open(file=800000004dcbd200) [ 53.348626] mvDmaDrv_mmap(file=800000004dcbd200) [ 53.353325] got a cookie, looking for bus 1 devfn 0 [ 53.358212] allocating for device 0000:01:00.0 [ 53.362966] dma_alloc_coherent() virt=800000004f600000 dma=0x4f600000 [ 53.369419] m->phys=0x4f600000 [ 53.372474] remap_pfn_range(phys=0x4f600000 vm_start=0x5c800000, vm_pgoff=0x4f600, vm_size=0x200000, ) mvDmaDrv mapped to 0x5c800000 WARNING! This computer system and network is PRIVATE and PROPRIETARY and may only be accessed by authorized users. Unauthorized use of this computer system or network is strictly prohibited . ROM_116_02_01_LCC4_0 login: Check MVDD init completed. [waiting:3s] [000101|00:00:04.673|MVDM|DUS_LOG|2|156|ERROR|49000]FW Not support ONE LOG [000101|00:00:04.684|MVDM|MFS|2|152|ERROR|70002]fail to open inservice file!!! [000101|00:00:04.703|IPSCM|DUS_LOG|2|156|ERROR|49000]FW Not support ONE LOG CTRL-A Z for help | 115200 8N1 | NOR | Minicom 2.10 | VT102 | Offline | ttyUSB0